Wraps by car

Fiat Brava wrap

The Fiat Brava wrap page covers the first generation of this compact hatchback, produced from 1995 to 2001. A full vinyl wrap of the Brava takes about 49 ft (15 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan on about 61 ft (18.5 m). The car is also known simply as the Brava.

1generations15 mof film for a full wrap

Fiat Brava, first generation, factory photo
Fiat Brava, first generation. Factory color shown.

Fiat Brava wrap colors and ideas

  • Brava black wrap
  • Brava white wrap
  • Brava gray wrap
  • Brava silver wrap
  • Brava red wrap
  • Brava blue wrap
  • Brava green wrap
  • Brava yellow wrap
  • Brava orange wrap
  • Brava purple wrap
  • Brava pink wrap
  • Brava teal wrap
  • Brava brown wrap
  • Brava gold wrap
  • Brava chrome wrap
  • Brava color shift wrap
  • Brava carbon fiber wrap
  • Brava camo and patterned wrap

How much vinyl to wrap a Fiat Brava

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1995–2001hatchback (5 doors)164.8 in (4,187 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Brava wrap cost factors

Brava wrap cost depends on the film type and the condition of the paint. A full wrap of the Brava needs about 49 ft (15 m) of cast film, while chrome or patterned film pushes the amount to about 61 ft (18.5 m). The tailgate with the rear glass adds cutting time, which affects the labor. The car's age matters because panels may need extra prep before the film goes on.

  • Film for a full wrap: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: hatchback (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Brava wraps by generation

Swipe sideways. Tap a card for the full description.

Fiat Brava, first generation, factory photo
Factory color shown

1995–2001 Brava hatchback (first generation)

1995–2001hatchback (5 doors)164.8 in (4,187 mm)

The first generation Fiat Brava is a compact hatchback built from 1995 to 2001. On a car of these years, the panels may be original or repainted, and a test spot comes before a full wrap. The film estimate for this body is about 49 ft (15 m) of 60-inch (1.52 m) cast film. The tailgate's rear glass means the film edge is set at the glass line.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Brava

Partial wrap options for the Fiat Brava include the roof, hood, and mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) can be applied to the front end as a clear film. These smaller jobs use less material than a full wrap and can be done in stages.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Fiat Brava: body, cut-outs and film

The Fiat Brava vinyl wrap covers a five-door hatchback with an overall length of 164.8 in (4,187 mm). This compact body has a tailgate with the rear glass in it, so the film ends at the edge of the glass. The size means a full wrap uses moderate material, but the tailgate design requires careful trimming around the window. The Brava's short overhangs and rounded panels call for patient stretching of the film.

Brava wrap ideas start with the tailgate, where the film must be cut along the edge of the rear glass. The door handles, mirrors, and badges are removed or masked for clean cut-outs. The front bumper and grille come off for better film adhesion behind the edges. The roof rails, if fitted, are dropped to wrap under them.

If you want to know how much vinyl to wrap a Brava, the first generation is the only one in this catalog. It was built from 1995 to 2001, and the body dimensions stayed the same through those years. For a full wrap, the film estimate is about 49 ft (15 m) of 60-inch (1.52 m) cast film. With chrome or patterned film, the takeoff is about 61 ft (18.5 m).

Questions about wrapping a Fiat Brava

How much vinyl does it take to wrap a Fiat Brava?

A Fiat Brava takes about 49 ft (15 m) of 60-inch (1.52 m) cast film for a full wrap. If you use chrome or patterned film, the amount is about 61 ft (18.5 m). The estimate covers the exterior of the five-door hatchback. The tailgate glass is not wrapped, so the film stops at its edge.

Can I wrap only the hood or the roof of a Brava?

Yes, you can wrap only the hood or the roof of a Brava. Partial wrap options for this car include the roof, hood, and mirror caps. A chrome delete on the window trim and badges is another smaller job. Paint protection film on the front end is also possible without a full wrap.

Is a Brava hard to wrap?

A Brava is not especially hard to wrap, but the tailgate adds work because the film must end at the edge of the rear glass. The car's 164.8 in (4,187 mm) length is manageable for a compact hatchback. The rounded panels of the 1995–2001 body need careful stretching of the film. The age of the paint may require extra prep before the wrap.

How many generations of the Brava does this page cover?

This page covers one generation of the Fiat Brava, produced from 1995 to 2001. The first generation is the only body style in the catalog. It is a five-door hatchback with a tailgate that includes the rear glass. A full wrap of this generation uses about 49 ft (15 m) of 60-inch (1.52 m) cast film.