Wraps by car

Kia X-Trek wrap

A Kia X-Trek wrap covers the whole first-generation van built from 2003 to 2006. The minivan has one body style with five doors. A full vinyl wrap of this body takes about 66 ft (20 m) of 60-inch (1.52 m) cast film.

1generations20 mof film for a full wrap

Kia X-Trek, first generation, factory photo
Kia X-Trek, first generation. Factory color shown.

Kia X-Trek wrap colors and ideas

  • X-Trek black wrap
  • X-Trek white wrap
  • X-Trek gray wrap
  • X-Trek silver wrap
  • X-Trek red wrap
  • X-Trek blue wrap
  • X-Trek green wrap
  • X-Trek yellow wrap
  • X-Trek orange wrap
  • X-Trek purple wrap
  • X-Trek pink wrap
  • X-Trek teal wrap
  • X-Trek brown wrap
  • X-Trek gold wrap
  • X-Trek chrome wrap
  • X-Trek color shift wrap
  • X-Trek carbon fiber wrap
  • X-Trek camo and patterned wrap

How much vinyl to wrap a Kia X-Trek

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2003–2006van (5 doors)176.8 in (4,490 mm)about 66 ft (20 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m)

X-Trek wrap cost factors

X-Trek wrap cost is based on the area of the body, the type of film and the amount of disassembly. A full wrap of this 176.8 in (4,490 mm) van needs about 66 ft (20 m) of cast film for a solid color. Chrome or patterned film adds material, about 76 ft (23 m), and more time for matching. Removing door handles, badges and roof rails adds labor to the job.

  • Film for a full wrap: about 66 ft (20 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).
  • Body: van (5 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.

X-Trek wraps by generation

Swipe sideways. Tap a card for the full description.

Kia X-Trek, first generation, factory photo
Factory color shown

2003–2006 X-Trek van (first generation)

2003–2006van (5 doors)176.8 in (4,490 mm)

The first-generation Kia X-Trek has sliding side doors that affect the wrap layout. The tracks stay bare and decide where the film is cut, so the line is straight and even. Installers cut the film along the track before wrapping the door panel. This keeps the door operating smoothly without scraping the film.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 66 ft (20 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).

Roof, hood, chrome delete and PPF on an X-Trek

The X-Trek chrome delete covers window trim and badges with black film, leaving the body color. A partial wrap can cover the roof, hood and mirror caps in a different color or finish. Paint protection film (PPF) is clear film applied to the front end to guard against stone chips. These smaller jobs use less material than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Kia X-Trek: body, cut-outs and film

A Kia X-Trek vinyl wrap on this minivan means working with a body 176.8 in (4,490 mm) long. The single van body style has large flat side panels, so film is applied in long runs. The tailgate and hood are large enough to use full-width pieces. Door handles, mirrors and bumper recesses need careful trimming.

X-Trek wrap ideas start with the sliding side doors and their exposed tracks. The tracks stay bare, and the film is cut along them for a clean edge. Badges and door handles are removed for a better finish. The roof rails remain visible and can be covered in a contrasting color.

How much vinyl to wrap an X-Trek depends on the film and the finish you choose. A solid color needs about 66 ft (20 m) of 60-inch (1.52 m) cast film. Chrome or patterned film needs more material, about 76 ft (23 m), because the pattern must be matched. The extra film helps line up the pattern at the doors and the tailgate.

Questions about wrapping a Kia X-Trek

How much vinyl does it take to wrap a Kia X-Trek?

A full wrap of a Kia X-Trek takes about 66 ft (20 m) of 60-inch (1.52 m) cast film for a solid color. A chrome or patterned film needs about 76 ft (23 m) because the pattern must be matched at seams. The extra film accounts for waste and alignment on the large side panels.

Are the sliding doors of an X-Trek wrapped?

Yes, the sliding doors of an X-Trek are wrapped, but the tracks are not. The tracks stay bare so the door can slide, and the film is cut along them. The door panel itself is covered up to the track line. This is standard for any van with sliding doors.

Can I wrap only the hood or the roof of an X-Trek?

Yes, you can wrap only the hood or the roof of an X-Trek. A partial wrap is a common choice for a contrasting color on the roof, hood and mirror caps. The hood and roof are large enough to use a full-width piece of film.

Is an X-Trek hard to wrap?

An X-Trek is not the hardest van to wrap, but the sliding doors add work. The tracks stay bare, so the film must be cut carefully along them. The van is 176.8 in (4,490 mm) long, so large side panels need two installers or a helper. Door handles, badges and roof rails must be removed for a clean finish.