Wraps by car

Mazda 6 MPS wrap

The Mazda 6 MPS wrap page covers the first generation, sold from 2005 to 2007. This one-generation catalog gives a full wrap estimate for the sedan body. A complete wrap of a Mazda 6 MPS takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. A vinyl wrap in chrome or a patterned film needs about 67 ft (20.5 m) instead.

1generations17.5 mof film for a full wrap

Mazda 6 MPS, first generation, factory photo
Mazda 6 MPS, first generation. Factory color shown.

Mazda 6 MPS wrap colors and ideas

  • Mazda 6 MPS black wrap
  • Mazda 6 MPS white wrap
  • Mazda 6 MPS gray wrap
  • Mazda 6 MPS silver wrap
  • Mazda 6 MPS red wrap
  • Mazda 6 MPS blue wrap
  • Mazda 6 MPS green wrap
  • Mazda 6 MPS yellow wrap
  • Mazda 6 MPS orange wrap
  • Mazda 6 MPS purple wrap
  • Mazda 6 MPS pink wrap
  • Mazda 6 MPS teal wrap
  • Mazda 6 MPS brown wrap
  • Mazda 6 MPS gold wrap
  • Mazda 6 MPS chrome wrap
  • Mazda 6 MPS color shift wrap
  • Mazda 6 MPS carbon fiber wrap
  • Mazda 6 MPS camo and patterned wrap

How much vinyl to wrap a Mazda 6 MPS

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2005–2007sedan (4 doors)186.6 in (4,740 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)

Mazda 6 MPS wrap cost factors

Mazda 6 MPS wrap cost depends on the film type, the amount used, and how much labor the body needs. The standard estimate is about 57 ft (17.5 m) of 60-inch (1.52 m) cast film, while chrome or patterned film raises the figure to about 67 ft (20.5 m). A car of this age may need extra prep if the paint is rough or panels have been repainted. Removing and reinstalling parts like mirrors and badges also adds time.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).
  • Body: sedan (4 doors).

Mazda 6 MPS wraps by generation

Swipe sideways. Tap a card for the full description.

Mazda 6 MPS, first generation, factory photo
Factory color shown

2005–2007 Mazda 6 MPS sedan (first generation)

2005–2007sedan (4 doors)186.6 in (4,740 mm)

The first generation Mazda 6 MPS from 2005 to 2007 has paint that may be original or resprayed. A test spot on each panel shows whether the film will lift old clear coat. The sedan's length of 186.6 in (4,740 mm) means a full wrap uses about 57 ft (17.5 m) of film. Because the car is nearly twenty years old, the installer checks for rust and stone chips before laying vinyl.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Roof, hood, chrome delete and PPF on a Mazda 6 MPS

A partial wrap on a Mazda 6 MPS works on the roof, hood, or mirror caps. A Mazda 6 MPS chrome delete covers the window trim and badges with black film. Clear paint protection film (PPF) on the front end shields the bumper, hood edge, and mirrors. These smaller jobs leave the doors and rear quarter panels unwrapped.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Mazda 6 MPS: body, cut-outs and film

A Mazda 6 MPS vinyl wrap starts with the sedan's four doors and mid-size proportions. The car is 186.6 in (4,740 mm) long, so a full wrap means film over a long roofline and deep bumpers. Fewer doors than a wagon or SUV means less area but more care around the rear arches. The single body style keeps panel shapes consistent for a smoother install.

Mazda 6 MPS wrap ideas should account for the front bumper, side skirts, and rear bumper. These parts need relief cuts and heat shaping because of their deep contours. The door handles, mirrors, and badges come off for cleaner edges. The hood scoop on the MPS is a small panel that needs its own inlay or careful bridging.

How much vinyl to wrap a Mazda 6 MPS depends on the generation, but this page covers only the first one. The GG body from 2005 to 2007 is the only generation in the catalog. For that car, the film estimate stays the same across all production years. No later generation exists for the 6 MPS, so there is no second body to compare.

Questions about wrapping a Mazda 6 MPS

How much vinyl does it take to wrap a Mazda 6 MPS?

A Mazda 6 MPS takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film for a full wrap. If you choose chrome or patterned film, plan on about 67 ft (20.5 m). These figures cover the first-generation sedan body from 2005 to 2007.

Can I wrap only the hood or the roof of a Mazda 6 MPS?

Yes, you can wrap only the hood or the roof of a Mazda 6 MPS. The partial wrap options for this car include the roof, hood, and mirror caps. A chrome delete on the window trim and badges is another small job. Clear paint protection film on the front end is also available without wrapping the whole car.

Is a Mazda 6 MPS hard to wrap?

A Mazda 6 MPS is not the easiest car to wrap, but its size and age add work. The sedan is 186.6 in (4,740 mm) long, so a full wrap uses about 57 ft (17.5 m) of film. The front bumper, side skirts, and rear bumper have deep contours that need extra heat and relief cuts. On a car from 2005 to 2007, the installer must test the paint before laying film.

How many generations of the Mazda 6 MPS does this page cover?

This page covers one generation of the Mazda 6 MPS. The first generation was sold from 2005 to 2007, and only that generation exists in the catalog.