Wraps by car

Mitsuoka MC-1 wrap

The Mitsuoka MC-1 wrap is a full vinyl wrap for a single-generation mini coupe produced from 1998 to 2007. The first generation is the only body this car was offered in. A complete color change wrap of the newest body takes about 21 ft (6.5 m) of 60-inch (1.52 m) cast film.

1generations6.5 mof film for a full wrap

Mitsuoka MC-1, first generation, factory photo
Mitsuoka MC-1, first generation. Factory color shown.

Mitsuoka MC-1 wrap colors and ideas

  • Mitsuoka MC-1 black wrap
  • Mitsuoka MC-1 white wrap
  • Mitsuoka MC-1 gray wrap
  • Mitsuoka MC-1 silver wrap
  • Mitsuoka MC-1 red wrap
  • Mitsuoka MC-1 blue wrap
  • Mitsuoka MC-1 green wrap
  • Mitsuoka MC-1 yellow wrap
  • Mitsuoka MC-1 orange wrap
  • Mitsuoka MC-1 purple wrap
  • Mitsuoka MC-1 pink wrap
  • Mitsuoka MC-1 teal wrap
  • Mitsuoka MC-1 brown wrap
  • Mitsuoka MC-1 gold wrap
  • Mitsuoka MC-1 chrome wrap
  • Mitsuoka MC-1 color shift wrap
  • Mitsuoka MC-1 carbon fiber wrap
  • Mitsuoka MC-1 camo and patterned wrap

How much vinyl to wrap a Mitsuoka MC-1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1998–2007coupe69.1 in (1,755 mm)about 21 ft (6.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 28 ft (8.5 m)

Mitsuoka MC-1 wrap cost factors

Mitsuoka MC-1 wrap cost depends on the size of the car and the condition of its paint. A full wrap of the 69.1 in (1,755 mm) coupe needs less film than a larger car, which lowers material use. Paint correction or panel repair before wrapping adds labor time. The choice of a standard color or a chrome or patterned film changes the film cost, with the patterned option needing about 28 ft (8.5 m).

  • Film for a full wrap: about 21 ft (6.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 28 ft (8.5 m).
  • Body: coupe.

Mitsuoka MC-1 wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsuoka MC-1, first generation, factory photo
Factory color shown

1998–2007 Mitsuoka MC-1 coupe (first generation)

1998–2007coupe69.1 in (1,755 mm)

The first generation Mitsuoka MC-1 spans 1998–2007 and may have original or repainted panels. Before a full wrap, an installer tests a small spot on each panel to see if the paint will hold the film. Repainted panels can peel when the wrap is removed, so the installer may advise against wrapping those areas. A careful test spot also checks for clear coat failure on old paint.

Film: about 21 ft (6.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 28 ft (8.5 m).

Roof, hood, chrome delete and PPF on a Mitsuoka MC-1

Partial wrap work on a Mitsuoka MC-1 covers the roof, hood, and mirror caps as separate jobs. Chrome delete changes the window trim and badges to black film for a consistent look. Paint protection film (PPF) can be applied as clear film on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Mitsuoka MC-1: body, cut-outs and film

The Mitsuoka MC-1 vinyl wrap covers a short coupe body that measures 69.1 in (1,755 mm) in length. A single body style means every car uses the same panel count and the same film estimate. The small size keeps material use low, but curved panels benefit from a cast film with good conformability.

Mitsuoka MC-1 wrap ideas begin with the small trim parts that need extra labor. The badges and window trim come off for clean edges. The door handles and mirror caps are removed before film is applied. The front bumper curves tightly, so an installer may use inlays to avoid overstretching the vinyl.

How much vinyl to wrap a Mitsuoka MC-1 changes only by paint condition because the car has one generation. A car with original paint from 1998–2007 may need less prep than a repainted one. The 69.1 in (1,755 mm) length stays constant for every year. The estimate of 21 ft (6.5 m) of 60-inch (1.52 m) cast film fits any year of this body.

Questions about wrapping a Mitsuoka MC-1

How much vinyl does it take to wrap a Mitsuoka MC-1?

Yes, a Mitsuoka MC-1 takes about 21 ft (6.5 m) of 60-inch (1.52 m) cast film for a full wrap. That estimate is for the standard color change film on the first-generation coupe. A chrome or patterned film needs about 28 ft (8.5 m) because of pattern matching.

Can I wrap only the hood or the roof of a Mitsuoka MC-1?

Yes, you can wrap only the hood or the roof of a Mitsuoka MC-1 as a partial wrap job. These smaller areas use less film and can be done without touching the rest of the car. Mirror caps are another common partial wrap option on this mini coupe.

Is a Mitsuoka MC-1 hard to wrap?

A Mitsuoka MC-1 is not especially hard to wrap, but the small 69.1 in (1,755 mm) body has tight curves on the bumpers. The installer needs to remove badges, window trim, door handles, and mirror caps to get clean edges. Original paint from 1998–2007 may need a test spot before the full wrap.

How many generations of the Mitsuoka MC-1 does this page cover?

This page covers one generation of the Mitsuoka MC-1. The car was produced from 1998 to 2007 with only the first generation in the catalog.