Wraps by car

Mitsuoka Zero 1 wrap

The Mitsuoka Zero 1 wrap covers a single-generation sports car, the convertible built from 1996 to 2000. A full vinyl wrap of this body takes about 34 ft (10.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film raises the estimate to about 44 ft (13.5 m). This page lists what the installer needs to know before wrapping one.

1generations10.5 mof film for a full wrap

Mitsuoka Zero 1, first generation, factory photo
Mitsuoka Zero 1, first generation. Factory color shown.

Mitsuoka Zero 1 wrap colors and ideas

  • Zero 1 black wrap
  • Zero 1 white wrap
  • Zero 1 gray wrap
  • Zero 1 silver wrap
  • Zero 1 red wrap
  • Zero 1 blue wrap
  • Zero 1 green wrap
  • Zero 1 yellow wrap
  • Zero 1 orange wrap
  • Zero 1 purple wrap
  • Zero 1 pink wrap
  • Zero 1 teal wrap
  • Zero 1 brown wrap
  • Zero 1 gold wrap
  • Zero 1 chrome wrap
  • Zero 1 color shift wrap
  • Zero 1 carbon fiber wrap
  • Zero 1 camo and patterned wrap

How much vinyl to wrap a Mitsuoka Zero 1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1996–2000convertible (2 doors)143.1 in (3,635 mm)about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m)

Zero 1 wrap cost factors

Zero 1 wrap cost depends on film type, the amount of disassembly, and the condition of the paint. The car uses about 34 ft (10.5 m) of 60-inch cast film, while chrome or patterned film raises the material total to about 44 ft (13.5 m). The convertible top and the folding roof add time to the job because the installer works around their edges. Removing trim around the windshield and the rocker panels also affects the final quote.

  • Film for a full wrap: about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Zero 1 wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsuoka Zero 1, first generation, factory photo
Factory color shown

1996–2000 Zero 1 convertible (first generation)

1996–2000convertible (2 doors)143.1 in (3,635 mm)

The first generation of the Mitsuoka Zero 1 is an open-top convertible with a fabric or folding hard top. The fabric top is not wrapped, and the film ends where the top meets the body. A folding hard top is wrapped as panels of its own, not as one continuous piece. The installer works the film edge along the beltline and keeps the cut clean where the roof opens.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).

Roof, hood, chrome delete and PPF on a Zero 1

Partial wrap on a Zero 1 can cover the hood, mirror caps, or rear deck. Zero 1 chrome delete means the window trim and badges are covered with black film. Paint protection film (PPF) on the front end protects the nose and the headlight surrounds. These jobs use less material than a full color change wrap and leave the original color visible elsewhere.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Mitsuoka Zero 1: body, cut-outs and film

A Mitsuoka Zero 1 vinyl wrap follows the clean lines of a small two-door convertible. The body measures 143.1 in (3,635 mm) in length, so one roll of standard-width film is enough for a full color change. The fabric top is not covered, which keeps material use lower than on a fixed-roof car of the same size. The wrap ends where the top begins, so the installer plans seams along that edge.

Zero 1 wrap ideas start with the one body style and the points that make film work harder on this car. The convertible body means a fabric top is not wrapped and the film ends where it begins. If the car has a folding hard top, each of its panels is wrapped as its own piece. The rear deck and the area behind the seats need careful inlays because the top folds close to the film.

How much vinyl to wrap a Zero 1 does not change between generations, because the catalog shows one generation only. The 1996–2000 convertible is the only body style, so the film estimate stays the same for every car. A full wrap takes about 34 ft (10.5 m) of 60-inch film, and chrome or patterned film needs about 44 ft (13.5 m). The installer counts the same amount for the first-year car and the last-year car.

Questions about wrapping a Mitsuoka Zero 1

How much vinyl does it take to wrap a Mitsuoka Zero 1?

A Mitsuoka Zero 1 full wrap takes about 34 ft (10.5 m) of 60-inch cast film. For chrome or patterned film the estimate rises to about 44 ft (13.5 m). The number is for the newest body in the catalog, the 1996–2000 convertible.

Is the top of a Zero 1 wrapped?

No, the top of a Zero 1 is not wrapped. A fabric top stays uncovered and the film ends where the top begins. A folding hard top is not wrapped as a whole; each panel of the roof is wrapped on its own.

Can I wrap only the hood or the roof of a Zero 1?

Yes, a partial wrap can cover only the hood or another small panel like a mirror cap or the rear deck. A Zero 1 chrome delete covers only the window trim and badges with black film. Paint protection film can be put on just the front end.

Is a Zero 1 hard to wrap?

A Zero 1 is small, but the convertible body adds work to a wrap. The fabric top is not wrapped and the film must end cleanly where the top begins. If a folding hard top is fitted, each panel is wrapped separately. The car is 143.1 in (3,635 mm) long, so the installer handles a compact surface but works around the roof hinges and weather seals.