Wraps by car

Proton Exora wrap

The Proton Exora wrap covers the full minivan body of the first generation, produced from 2009 to now. A full vinyl wrap of this five-door van takes about 67 ft (20.5 m) of 60-inch (1.52 m) cast film. With chrome or patterned film, the estimate rises to about 79 ft (24 m). The page below explains the body, cut-outs, and film amounts for an Exora wrap.

1generations20.5 mof film for a full wrap

Proton Exora, first generation, factory photo
Proton Exora, first generation. Factory color shown.

Proton Exora wrap colors and ideas

  • Exora black wrap
  • Exora white wrap
  • Exora gray wrap
  • Exora silver wrap
  • Exora red wrap
  • Exora blue wrap
  • Exora green wrap
  • Exora yellow wrap
  • Exora orange wrap
  • Exora purple wrap
  • Exora pink wrap
  • Exora teal wrap
  • Exora brown wrap
  • Exora gold wrap
  • Exora chrome wrap
  • Exora color shift wrap
  • Exora carbon fiber wrap
  • Exora camo and patterned wrap

How much vinyl to wrap a Proton Exora

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–nowvan (5 doors)180.8 in (4,592 mm)about 67 ft (20.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 79 ft (24 m)

Exora wrap cost factors

Exora wrap cost depends on film type, coverage, and the prep work for a minivan of 180.8 in (4,592 mm). The basic full wrap uses about 67 ft (20.5 m) of 60-inch (1.52 m) cast film, while chrome or patterned film needs about 79 ft (24 m). A partial wrap of the roof or hood uses less film than a full wrap, so material cost is lower. The sliding door tracks add labor because the installer cuts around them and keeps the edges sealed.

  • Film for a full wrap: about 67 ft (20.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 79 ft (24 m).
  • Body: van (5 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.

Exora wraps by generation

Swipe sideways. Tap a card for the full description.

Proton Exora, first generation, factory photo
Factory color shown

2009–now Exora van (first generation)

2009–nowvan (5 doors)180.8 in (4,592 mm)

The first-generation Proton Exora, built from 2009 to now, has sliding side doors with tracks that stay bare and decide where the film is cut. The installer runs the vinyl up to the edge of the track recess, leaving the channel itself uncovered. This cut line runs along the rear side panels on both sides of the van. The same approach is used on the door itself, where the film stops short of the track.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 67 ft (20.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 79 ft (24 m).

Roof, hood, chrome delete and PPF on an Exora

Smaller Exora jobs include a partial wrap of the roof, hood, or mirror caps, which many owners choose for a color accent. An Exora chrome delete covers the window trim and badges with black film, giving the van a darker look. Paint protection film (PPF) in a clear film on the front end shields the hood and bumper from stone chips. These options use less film than a full wrap and can be combined.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Proton Exora: body, cut-outs and film

The Proton Exora vinyl wrap has to handle a long minivan body of 180.8 in (4,592 mm) and sliding side doors. The tall, flat panels of a van give the installer large surfaces, but the door tracks interrupt the rear side panels. A full wrap follows the body lines without covering the tracks, so the film is trimmed around them. The five-door layout means five door handles and two mirror caps are part of the job.

Exora wrap ideas start with the sliding door tracks, which stay bare and decide where the film is cut. The tracks cannot be wrapped because the sliding mechanism would tear the film. Installers also remove badges, door handles, and mirror caps for a clean edge, then refit them after wrapping. The front and rear bumpers need relief cuts around sensors and lights, and the roof has channels that call for careful trimming.

To find how much vinyl to wrap an Exora, the first generation counts on a single body style with no major size changes from 2009 to now. The film estimate of about 67 ft (20.5 m) of 60-inch (1.52 m) cast film applies to every production year. If the wrap uses chrome or patterned film, the needed amount is about 79 ft (24 m) because matching patterns adds waste. The sliding door tracks do not change the total film, but they change how the rear panels are cut.

Questions about wrapping a Proton Exora

How much vinyl does it take to wrap a Proton Exora?

A full Proton Exora wrap takes about 67 ft (20.5 m) of 60-inch (1.52 m) cast film. If you use chrome or patterned film, the amount rises to about 79 ft (24 m). These figures cover the whole body, including the doors and bumpers, but not the sliding door tracks.

Are the sliding doors of an Exora wrapped?

No, the sliding door tracks of an Exora are not wrapped. The tracks stay bare because the sliding mechanism would catch and tear the film. The installer cuts the vinyl along the edge of the track and leaves the channel exposed.

Can I wrap only the hood or the roof of an Exora?

Yes, you can wrap only the hood or the roof of an Exora as a partial wrap. A partial wrap can also include the mirror caps, and it uses less film than a full wrap. Another small job is a chrome delete for the window trim and badges.

Is an Exora hard to wrap?

An Exora is moderately hard to wrap because of its sliding door tracks and long minivan body of 180.8 in (4,592 mm). The installer must cut the film around the tracks and keep the edges clean, which adds work. The large roof and tall sides also require careful handling of the 60-inch (1.52 m) film.