Wraps by car

Proton Putra wrap

This page covers the Proton Putra wrap in full. The Putra was produced for one generation from 1996 to 2004. A vinyl wrap of the complete coupe body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly 56 ft (17 m) to that figure.

1generations14 mof film for a full wrap

Proton Putra, first generation, factory photo
Proton Putra, first generation. Factory color shown.

Proton Putra wrap colors and ideas

  • Putra black wrap
  • Putra white wrap
  • Putra gray wrap
  • Putra silver wrap
  • Putra red wrap
  • Putra blue wrap
  • Putra green wrap
  • Putra yellow wrap
  • Putra orange wrap
  • Putra purple wrap
  • Putra pink wrap
  • Putra teal wrap
  • Putra brown wrap
  • Putra gold wrap
  • Putra chrome wrap
  • Putra color shift wrap
  • Putra carbon fiber wrap
  • Putra camo and patterned wrap

How much vinyl to wrap a Proton Putra

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1996–2004coupe (2 doors)166.3 in (4,225 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)

Putra wrap cost factors

A Putra wrap cost depends on the film area, the film type, and the labor to prepare and wrap the coupe. A full wrap uses about 46 ft (14 m) of 60-inch (1.52 m) cast film, or about 56 ft (17 m) for chrome or patterned film. The two long doors are large single pieces, so a shop may charge less labor per panel than on a four-door car. Paint condition on a 1996–2004 car also affects the prep work, because old or repainted panels need more cleaning and testing before film goes on.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Putra wraps by generation

Swipe sideways. Tap a card for the full description.

Proton Putra, first generation, factory photo
Factory color shown

1996–2004 Putra coupe (first generation)

1996–2004coupe (2 doors)166.3 in (4,225 mm)

The first generation Proton Putra was built from 1996 to 2004 as a two-door coupe. Paint age on a car of these years matters: panels may be original or repainted. A wrap shop does a test spot on one panel before a full wrap to check how the film adheres to the old paint. If the paint is weak, the wrap may lift when removed, so the installer will tell you which panels are safe to cover.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Roof, hood, chrome delete and PPF on a Putra

A partial wrap on a Proton Putra can cover the roof, the hood, or the mirror caps as separate jobs. A chrome delete covers the window trim and badges with black film. For paint protection film (PPF), the front end gets clear film to guard against stone chips. Each of these jobs uses much less film than a full body wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Proton Putra: body, cut-outs and film

A Proton Putra vinyl wrap covers a two-door coupe body 166.3 in (4,225 mm) long. The long side doors are each one large piece of film, so a full wrap uses wide material efficiently. The body has no complex roof or tailgate sections that break the wrap into many small panels. The wrap installer works the film around the coupe's rear window and bumper lines with heat.

Putra wrap ideas begin with the side doors, which take one large piece of film each. The door handles and side mirrors come off for a clean edge, but the camera or sensor cut-outs of newer cars are not needed here. The wrap shop trims openings for the fuel filler, door edges, and the badges on the rear panel. A chrome delete can cover the window trim and badges with black film on the same car.

How much vinyl to wrap a Putra depends on the single production generation. The first generation body from 1996 to 2004 uses about 46 ft (14 m) of standard cast film. No later body style changes the film estimate, so the figure stays the same for every year. A wrap shop still measures the car before cutting because repairs or repaints can alter panel gaps.

Questions about wrapping a Proton Putra

How much vinyl does it take to wrap a Proton Putra?

A full Proton Putra wrap takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. Chrome or patterned film needs more, about 56 ft (17 m), because of the material loss when matching patterns. The figure covers the complete coupe body of the only generation made.

Can I wrap only the hood or the roof of a Putra?

Yes, you can wrap only the hood or the roof of a Putra as a partial wrap. The roof, hood, and mirror caps are separate jobs that use much less film than a full wrap. A shop can also do a chrome delete on the window trim and badges.

Is a Putra hard to wrap?

A Proton Putra is not hard to wrap, but it adds work in a few areas. The two long side doors are each one large piece of film, so a single installer needs help or must work in sections. The body is 166.3 in (4,225 mm) long, which puts part of the roof and the rear bumper out of easy reach. The car has no complex body lines, but the old paint may need more prep before film is applied.

How many generations of the Putra does this page cover?

This page covers one generation of the Proton Putra. The first generation was produced from 1996 to 2004 as a two-door coupe. No other generations exist in the catalog, so all wrap information here is for that single body.