Wraps by car

Proton Preve wrap

The Proton Preve wrap page covers the single generation built since 2012 as a four-door compact sedan. A full vinyl wrap of this body takes about 56 ft (17 m) of 60-inch (1.52 m) cast film. Owners who choose a chrome or patterned film should plan for about 66 ft (20 m). We describe the body, tricky areas, partial jobs and the questions buyers ask before a wrap.

1generations17 mof film for a full wrap

Proton Preve, first generation, factory photo
Proton Preve, first generation. Factory color shown.

Proton Preve wrap colors and ideas

  • Preve black wrap
  • Preve white wrap
  • Preve gray wrap
  • Preve silver wrap
  • Preve red wrap
  • Preve blue wrap
  • Preve green wrap
  • Preve yellow wrap
  • Preve orange wrap
  • Preve purple wrap
  • Preve pink wrap
  • Preve teal wrap
  • Preve brown wrap
  • Preve gold wrap
  • Preve chrome wrap
  • Preve color shift wrap
  • Preve carbon fiber wrap
  • Preve camo and patterned wrap

How much vinyl to wrap a Proton Preve

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2012–nowsedan (4 doors)178.9 in (4,543 mm)about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m)

Preve wrap cost factors

Preve wrap cost depends on the number of panels, the film type and the prep work on a car of this size. A full color change wrap with 56 ft (17 m) of cast film requires more labor than a roof or hood wrap. Chrome delete adds time because window trim and badges are small and must be removed or masked. Paint correction before wrapping adds to the total and is often needed on a car built since 2012.

  • Film for a full wrap: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).
  • Body: sedan (4 doors).

Preve wraps by generation

Swipe sideways. Tap a card for the full description.

Proton Preve, first generation, factory photo
Factory color shown

2012–now Preve sedan (first generation)

2012–nowsedan (4 doors)178.9 in (4,543 mm)

The first generation Proton Preve was built from 2012 to the present as a four-door sedan. Its length of 178.9 in (4,543 mm) and simple three-box shape make film estimates consistent. On a car of these years, some panels may have been repainted, so a wrap shop should test adhesion in a small spot. That step prevents lifting on older paint and helps the installer plan the job.

Film: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).

Roof, hood, chrome delete and PPF on a Preve

A partial wrap on a Proton Preve covers the roof, hood or mirror caps and uses much less film than a full wrap. Preve chrome delete covers the window trim and badges with black film for a cleaner look. Paint protection film (PPF) on the front end is a clear film that guards the bumper, hood and fenders from stone chips. Each job can be done separately and does not require wrapping the whole sedan.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Proton Preve: body, cut-outs and film

A Proton Preve vinyl wrap must cover a sedan body 178.9 in (4,543 mm) long with four doors and a trunk. The roof, hood and rear deck are large flat panels that are straightforward to wrap. The lower door areas and rocker panels need more material and careful trimming. A full wrap uses the figures above, while a partial job uses far less.

Preve wrap ideas start with the areas that need cut-outs or removal before film is applied. The door handles, badges and trim come off for a clean installation, and the mirrors are wrapped separately. The front bumper has fog lamp openings and the grille is recessed, so the installer spends extra time there. Door edges and the trunk lip also require precise knifeless tape work.

To know how much vinyl to wrap a Preve, count the generation: this page has only the first generation, 2012–now. The body has not changed in size or shape, so the estimate stays the same across all years. A chrome or patterned film increases the figure because the pattern must be matched. A test spot is wise on older paint that may be original or repainted.

Questions about wrapping a Proton Preve

How much vinyl does it take to wrap a Proton Preve?

A Proton Preve takes about 56 ft (17 m) of 60-inch (1.52 m) cast film for a full color change wrap. For chrome or patterned film, plan on about 66 ft (20 m) because the pattern must be aligned. Partial jobs like the hood or roof need only a fraction of that amount.

Can I wrap only the hood or the roof of a Preve?

Yes, you can wrap only the hood or the roof of a Preve. A partial wrap can be limited to the roof, hood or mirror caps, and it uses less film than a full wrap. Chrome delete on the window trim and badges is another small job.

Is a Preve hard to wrap?

A Preve is not hard to wrap for an installer, but the front bumper and grille add time because of the fog lamp openings and recessed areas. The door handles, badges and trim must be removed or cut around carefully. Its length of 178.9 in (4,543 mm) means long roof and side panels that need two people to handle.

How many generations of the Preve does this page cover?

This page covers one generation of the Proton Preve: the first generation built from 2012 to the present. There have been no major body changes, so the wrap estimate stays the same.