Wraps by car

Proton Saga wrap

The Proton Saga wrap page covers two generations of this compact sedan and hatchback, from 1985 to the present. A full vinyl wrap of the newest Saga body takes about 52 ft (16 m) of 60-inch (1.52 m) cast film. The first generation spans 1985–2008, while the second generation runs from 2008 to the current model.

2generations16 mof film for a full wrap

Proton Saga, second generation, factory photo
Proton Saga, second generation. Factory color shown.

Proton Saga wrap colors and ideas

  • Saga black wrap
  • Saga white wrap
  • Saga gray wrap
  • Saga silver wrap
  • Saga red wrap
  • Saga blue wrap
  • Saga green wrap
  • Saga yellow wrap
  • Saga orange wrap
  • Saga purple wrap
  • Saga pink wrap
  • Saga teal wrap
  • Saga brown wrap
  • Saga gold wrap
  • Saga chrome wrap
  • Saga color shift wrap
  • Saga carbon fiber wrap
  • Saga camo and patterned wrap

How much vinyl to wrap a Proton Saga

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2008–nowsedan (4 doors)168.4 in (4,278 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)
1985–2008hatchback, sedan (4 or 5 doors)168.5 in (4,280 mm)about 48 ft (14.5 m) for the sedan to 49 ft (15 m) for the hatchback, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 61 ft (18.5 m)

Saga wrap cost factors

Saga wrap cost depends on the film type, the generation, and the condition of the paint. A full wrap of the second generation uses about 52 ft (16 m) of film, while the first generation uses 48–49 ft (14.5–15 m). Chrome or patterned film increases material to up to 61 ft (18.5 m). Paint age also matters because older cars may need more preparation before the vinyl goes on.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: sedan (4 doors).

Saga wraps by generation

Swipe sideways. Tap a card for the full description.

Proton Saga, second generation, factory photo
Factory color shown

2008–now Saga sedan (second generation)

2008–nowsedan (4 doors)168.4 in (4,278 mm)

The second generation Proton Saga, produced from 2008 to now, is a four-door sedan with paint that may be original or repainted. Before a full wrap, a test spot on the paint checks whether the film will adhere properly. This step is important on a car of these years because panel surfaces can vary. The installer will then plan the wrap around the 168.4 in (4,278 mm) body.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Proton Saga, first generation, factory photo
Factory color shown

1985–2008 Saga hatchback, sedan (first generation)

1985–2008hatchback, sedan (4 or 5 doors)168.5 in (4,280 mm)

The first generation Proton Saga, built from 1985 to 2008, came as a hatchback or a sedan with four or five doors. The body style decides the panel plan and the film amount, with the sedan taking about 48 ft (14.5 m) and the hatchback about 49 ft (15 m) of 60-inch (1.52 m) cast film. The hatchback also has a tailgate with the rear glass in it, so the film ends at the edge of the glass. This generation is slightly longer at 168.5 in (4,280 mm).

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 48 ft (14.5 m) for the sedan to 49 ft (15 m) for the hatchback, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Saga

For a Proton Saga, a partial wrap can cover the roof, hood, or mirror caps on their own. A chrome delete (bright trim covered with black film) is an option for the window trim and badges. Paint protection film (PPF) is available as clear film on the front end to guard against stone chips. These smaller jobs use less material than a full wrap and can be done on either generation.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Proton Saga: body, cut-outs and film

The Proton Saga vinyl wrap depends on a compact sedan body with four doors on the newest generation. Its 168.4 in (4,278 mm) length means a full wrap uses about 52 ft (16 m) of 60-inch (1.52 m) cast film. The older body is nearly the same size at 168.5 in (4,280 mm) and adds a hatchback option. These compact dimensions keep the film estimate close to a mid-size sedan.

Saga wrap ideas include removing badges and door handles for a cleaner finish, but the main attention goes to the tailgate on the first generation. That tailgate has the rear glass set into it, so the film ends at the edge of the glass rather than wrapping behind it. Cut-outs for the windshield, side glass, and lights are standard on both generations. You can also cover the roof and mirror caps as separate panels for a two-tone look.

How much vinyl to wrap a Saga changes between the two generations because of body styles and trim details. The first generation sedan takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film, while the hatchback takes about 49 ft (15 m). The second generation sedan takes about 52 ft (16 m) of the same film. If you choose chrome or patterned film, both generations can use up to about 61 ft (18.5 m).

Questions about wrapping a Proton Saga

How much vinyl does it take to wrap a Proton Saga?

A full Proton Saga wrap takes about 52 ft (16 m) of 60-inch (1.52 m) cast film for the second generation sedan. The first generation sedan needs about 48 ft (14.5 m) and the hatchback about 49 ft (15 m) of the same film. Chrome or patterned film can require up to about 61 ft (18.5 m) on either generation. The total film depends on the body style and the exact wrap design.

Can I wrap only the hood or the roof of a Saga?

Yes, you can wrap only the hood or the roof of a Proton Saga, and mirror caps are another partial option. A partial wrap covers individual panels rather than the whole car. For the Saga, the roof, hood, and mirror caps are the usual choices. This lets you change the look of one area without a full wrap.

Is a Saga hard to wrap?

A Proton Saga is not hard to wrap, but the first generation hatchback has a tailgate with the rear glass in it that adds a step. The film must end at the edge of the glass, which takes extra care. The compact size of the Saga, about 168.4–168.5 in (4,278–4,280 mm), keeps panel sizes manageable. The sedan shapes are straightforward for a vinyl wrap.

How many generations of the Saga does this page cover?

This page covers two generations of the Proton Saga. The first generation ran from 1985 to 2008 and the second from 2008 to the present. Both are compact cars with sedan bodies, and the first generation also offered a hatchback. Each generation has its own film estimate and wrap considerations.