Wraps by car

Subaru Baja wrap

The Subaru Baja wrap page covers the single generation produced from 2002 to 2006. A full vinyl wrap of the newest body takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film needs roughly 70 ft (21.5 m). The Baja is a mid-size pickup with four doors, which keeps the job straightforward for one installer.

1generations18.5 mof film for a full wrap

Subaru Baja, first generation, factory photo
Subaru Baja, first generation. Factory color shown.

Subaru Baja wrap colors and ideas

  • Baja black wrap
  • Baja white wrap
  • Baja gray wrap
  • Baja silver wrap
  • Baja red wrap
  • Baja blue wrap
  • Baja green wrap
  • Baja yellow wrap
  • Baja orange wrap
  • Baja purple wrap
  • Baja pink wrap
  • Baja teal wrap
  • Baja brown wrap
  • Baja gold wrap
  • Baja chrome wrap
  • Baja color shift wrap
  • Baja carbon fiber wrap
  • Baja camo and patterned wrap

How much vinyl to wrap a Subaru Baja

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2002–2006pickup (4 doors)193.3 in (4,910 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m)

Baja wrap cost factors

Baja wrap cost depends on the film type, the size of the vehicle, and how much disassembly the job needs. A full wrap of this 193.3 in (4,910 mm) pickup uses about 61 ft (18.5 m) of 60-inch (1.52 m) cast vinyl. Chrome or patterned material pushes the total to about 70 ft (21.5 m), which raises labor for alignment. Removing roof rails, door handles, and cladding adds time compared with wrapping over them.

  • Film for a full wrap: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).
  • Body: pickup (4 doors).
  • A pickup bed: the cab and the bed are wrapped as two bodies, and the inside of the bed is not wrapped.

Baja wraps by generation

Swipe sideways. Tap a card for the full description.

Subaru Baja, first generation, factory photo
Factory color shown

2002–2006 Baja pickup (first generation)

2002–2006pickup (4 doors)193.3 in (4,910 mm)

The first generation Subaru Baja treat the cab and the bed as two separate bodies for film. The inside of the bed stays bare because wrap film is not made to handle cargo abrasion. The tailgate and bed sides wrap down to the top edge of the inner bed wall. This split does not change the total film estimate, but it adds seam planning at the cab-to-bed gap.

A pickup bed: the cab and the bed are wrapped as two bodies, and the inside of the bed is not wrapped.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).

Roof, hood, chrome delete and PPF on a Baja

Partial wrap on a Subaru Baja can be limited to the roof, hood, and mirror caps for a two-tone look. A chrome delete covers window trim and badges with black film for a muted finish. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. None of these jobs requires wrapping the bed, so material use stays well below a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Subaru Baja: body, cut-outs and film

The Subaru Baja vinyl wrap is shaped by its pickup body style and 193.3 in (4,910 mm) length. The cab and the bed count as two separate areas for material planning. This mid-size footprint means the wrap uses less film than a full-size truck. The four-door cab has standard pillar and rocker sections that wrap in one piece each.

Baja wrap ideas start with the factory black cladding on the lower doors and bed sides. That cladding can be wrapped in a contrast color or left bare to break up a solid wrap. The roof rails and door handles come off for cleaner edges, while the badges are cut around unless the owner wants them removed. The fuel filler door needs a cut-out so the film edge does not lift at the hinge.

How much vinyl to wrap a Baja matters when you compare the single generation in this catalog. The 2002–2006 body is the only one, so film estimates stay the same across production years. Planning remains identical for every Baja because no second generation exists. An installer counts about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a complete color change.

Questions about wrapping a Subaru Baja

How much vinyl does it take to wrap a Subaru Baja?

A Subaru Baja needs about 61 ft (18.5 m) of 60-inch (1.52 m) cast vinyl for a full color change. That figure covers the cab and the bed sides as two separate bodies. If the film is chrome or has a pattern, the material goes up to about 70 ft (21.5 m) because the installer must match the design across panels.

Is the bed of a Baja wrapped?

No, the inside of the bed is not wrapped. The cab and the bed are wrapped as two bodies, but the bed floor and inner walls stay bare. Film on those surfaces would tear from cargo sliding, so the wrap stops at the top edge of the bed walls.

Can I wrap only the hood or the roof of a Baja?

Yes, a partial wrap on a Baja can cover only the hood or the roof. Mirror caps can be added to either job without much extra film. A chrome delete on window trim and badges is another small-area option. These partial jobs leave the bed unwrapped and use far less material than a full wrap.

Is a Baja hard to wrap?

A Baja adds work because the cab and bed are wrapped as two separate bodies. The total length of 193.3 in (4,910 mm) means large side panels, but the straight bed sides are easy to handle. The roof rails and door handles should come off for clean edges, which adds disassembly time. The inside of the bed stays bare, so no film is wasted on a high-wear area.