Wraps by car

Subaru Exiga wrap

The Subaru Exiga wrap page covers the first generation produced from 2008 to 2015. A full vinyl wrap of this wagon uses about 64 ft (19.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film requires about 74 ft (22.5 m) for complete coverage.

1generations19.5 mof film for a full wrap

Subaru Exiga, first generation, factory photo
Subaru Exiga, first generation. Factory color shown.

Subaru Exiga wrap colors and ideas

  • Exiga black wrap
  • Exiga white wrap
  • Exiga gray wrap
  • Exiga silver wrap
  • Exiga red wrap
  • Exiga blue wrap
  • Exiga green wrap
  • Exiga yellow wrap
  • Exiga orange wrap
  • Exiga purple wrap
  • Exiga pink wrap
  • Exiga teal wrap
  • Exiga brown wrap
  • Exiga gold wrap
  • Exiga chrome wrap
  • Exiga color shift wrap
  • Exiga carbon fiber wrap
  • Exiga camo and patterned wrap

How much vinyl to wrap a Subaru Exiga

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2008–2015wagon (5 doors)188.2 in (4,780 mm)about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m)

Exiga wrap cost factors

Exiga wrap cost depends on how much film the wagon needs and the labor for its size. The full wrap uses about 64 ft (19.5 m) of cast film, while chrome or patterned film pushes the amount to about 74 ft (22.5 m). Paint condition also matters, because a test spot on these 2008–2015 cars can reveal adhesion issues that add prep work. The straight body lines and single tailgate design keep labor predictable.

  • Film for a full wrap: about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).
  • Body: wagon (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Exiga wraps by generation

Swipe sideways. Tap a card for the full description.

Subaru Exiga, first generation, factory photo
Factory color shown

2008–2015 Exiga wagon (first generation)

2008–2015wagon (5 doors)188.2 in (4,780 mm)

Paint age on the first generation Subaru Exiga matters before a full wrap. Panels on this 2008–2015 wagon may be original or repainted, and a test spot comes before a full wrap. The installer checks adhesion on a small area to spot clear-coat failure or weak paint. That step prevents lifting when the film is removed later.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).

Roof, hood, chrome delete and PPF on an Exiga

Partial wrap or Exiga chrome delete are smaller jobs on the Subaru Exiga. The roof, hood, and mirror caps can be wrapped individually without covering the whole wagon. Chrome delete covers the window trim and badges with black film. Paint protection film (PPF) as a clear film on the front end guards against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Subaru Exiga: body, cut-outs and film

The Subaru Exiga vinyl wrap deals with one body style: a five-door wagon with a mid-size footprint. Its length of 188.2 in (4,780 mm) means the film estimate is based on that exact size. With only one generation, installers can plan the wrap without accounting for body changes across different years.

Exiga wrap ideas should account for the tailgate with the rear glass in it. The film ends at the edge of the glass, so no cut-out is needed around a separate window. Removing the tailgate handle or trim pieces may ease installation, but the design stays straightforward for a wagon.

How much vinyl to wrap an Exiga depends on the body code YA, which covers every trim of this wagon. The 60-inch (1.52 m) film width suits the roof and hood, while the length of 188.2 in (4,780 mm) sets the baseline for the job. Since only one generation exists, the figure of about 64 ft (19.5 m) holds for all production years from 2008 to 2015.

Questions about wrapping a Subaru Exiga

How much vinyl does it take to wrap a Subaru Exiga?

An Exiga wrap uses about 64 ft (19.5 m) of 60-inch (1.52 m) cast film for a full color change. If you choose chrome or patterned film, plan for about 74 ft (22.5 m) because the pattern repeat may require more material. These figures come from the wagon's length of 188.2 in (4,780 mm) and its five-door layout.

Can I wrap only the hood or the roof of an Exiga?

Yes, you can wrap only the hood or the roof of an Exiga. Partial wrap options include the roof, hood, and mirror caps as separate jobs. A chrome delete covers window trim and badges without touching large panels. Paint protection film on the front end is also done without a full wrap.

Is an Exiga hard to wrap?

An Exiga is not especially hard to wrap, but the tailgate with the rear glass in it adds a step. The film must end at the edge of the glass, so the installer trims precisely around that area. The wagon's length of 188.2 in (4,780 mm) means long roof and side panels need careful handling to avoid stretch marks.

How many generations of the Exiga does this page cover?

This page covers one generation of the Subaru Exiga, produced from 2008 to 2015. The first generation uses the YA body code and comes as a five-door wagon. All film estimates and wrap notes refer to that single generation.