Wraps by car

Subaru R1 wrap

This page covers the Subaru R1 wrap and the vinyl wrap film a full wrap of this one-generation mini takes. The Subaru R1 was built from 2005 to 2010 as a three-door hatchback. A complete color change wrap on the newest body uses about 43 ft (13 m) of 60-inch (1.52 m) cast film.

1generations13 mof film for a full wrap

Subaru R1, first generation, factory photo
Subaru R1, first generation. Factory color shown.

Subaru R1 wrap colors and ideas

  • Subaru R1 black wrap
  • Subaru R1 white wrap
  • Subaru R1 gray wrap
  • Subaru R1 silver wrap
  • Subaru R1 red wrap
  • Subaru R1 blue wrap
  • Subaru R1 green wrap
  • Subaru R1 yellow wrap
  • Subaru R1 orange wrap
  • Subaru R1 purple wrap
  • Subaru R1 pink wrap
  • Subaru R1 teal wrap
  • Subaru R1 brown wrap
  • Subaru R1 gold wrap
  • Subaru R1 chrome wrap
  • Subaru R1 color shift wrap
  • Subaru R1 carbon fiber wrap
  • Subaru R1 camo and patterned wrap

How much vinyl to wrap a Subaru R1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2005–2010hatchback (3 doors)129.3 in (3,285 mm)about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Subaru R1 wrap cost factors

A Subaru R1 wrap cost depends on the film area, the film type, and the labor steps on this body. The full wrap area is about 43 ft (13 m), and chrome or patterned film raises the estimate to about 51 ft (15.5 m). Paint age also matters on a 2005–2010 car, where panels may be original or repainted, and a test spot comes before a full wrap.

  • Film for a full wrap: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

Subaru R1 wraps by generation

Swipe sideways. Tap a card for the full description.

Subaru R1, first generation, factory photo
Factory color shown

2005–2010 Subaru R1 hatchback (first generation)

2005–2010hatchback (3 doors)129.3 in (3,285 mm)

The first generation Subaru R1 is the only generation, built from 2005 to 2010. It is a three-door hatchback with a 129.3 in (3,285 mm) body. Paint age on a car of these years is a real check: panels may be original or repainted, and a test spot comes before a full wrap.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Subaru R1

Smaller jobs on a Subaru R1 include a partial wrap of the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film that protects the front end from stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Subaru R1: body, cut-outs and film

A Subaru R1 vinyl wrap is a small job by car size, but the body still needs careful film planning. The car is a short three-door hatchback at 129.3 in (3,285 mm) long. The tailgate and the two long side doors add large flat areas that use film efficiently. A mini body means fewer panels to wrap, but every panel still has to be measured twice.

Subaru R1 wrap ideas start with the parts that need cut-outs or come off for a clean install. The tailgate has the rear glass in it, so the film ends at the edge of the glass. Each of the two long side doors is one large piece of film, which reduces seams but requires careful squeegee work. Door handles, mirrors, and badges come off before the film goes on.

When you work out how much vinyl to wrap a Subaru R1, the number stays the same because there is only one generation. The 2005–2010 hatchback shares one body shape, so film estimates from the newest body fit all years. Counting film does not change between early and late cars the way it does on a model with two generations.

Questions about wrapping a Subaru R1

How much vinyl does it take to wrap a Subaru R1?

A Subaru R1 takes about 43 ft (13 m) of 60-inch (1.52 m) cast film for a full wrap. That figure is the estimate for the newest body of this single-generation mini. If you choose chrome or patterned film, plan for about 51 ft (15.5 m).

Can I wrap only the hood or the roof of a Subaru R1?

Yes, you can wrap only the hood or the roof of a Subaru R1. A partial wrap on this car often covers the roof, hood, or mirror caps. Those panels match the small size of the car and use far less film than a full wrap.

Is a Subaru R1 hard to wrap?

A Subaru R1 is not especially hard to wrap, but two points add work. The tailgate has the rear glass in it, so the film must end at the edge of the glass. Each of the two long side doors is one large piece of film, which needs careful handling to avoid wrinkles.

How many generations of the Subaru R1 does this page cover?

This page covers one generation of the Subaru R1. The car was produced from 2005 to 2010, and only one generation appears in the catalog.