Wraps by car

Subaru Vivio wrap

The Subaru Vivio wrap page covers the first generation, the only generation in this catalog, produced from 1992 to 1998. A full vinyl wrap of the newest body takes about 38 ft (11.5 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, plan on about 48 ft (14.5 m).

1generations11.5 mof film for a full wrap

Subaru Vivio, first generation, factory photo
Subaru Vivio, first generation. Factory color shown.

Subaru Vivio wrap colors and ideas

  • Vivio black wrap
  • Vivio white wrap
  • Vivio gray wrap
  • Vivio silver wrap
  • Vivio red wrap
  • Vivio blue wrap
  • Vivio green wrap
  • Vivio yellow wrap
  • Vivio orange wrap
  • Vivio purple wrap
  • Vivio pink wrap
  • Vivio teal wrap
  • Vivio brown wrap
  • Vivio gold wrap
  • Vivio chrome wrap
  • Vivio color shift wrap
  • Vivio carbon fiber wrap
  • Vivio camo and patterned wrap

How much vinyl to wrap a Subaru Vivio

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1992–1998hatchback (3 or 5 doors)129.9 in (3,300 mm)about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m)

Vivio wrap cost factors

Vivio wrap cost depends on the film type, the condition of the paint, and how much of the car you wrap. The car's small size of 129.9 in (3,300 mm) means a full wrap uses about 38 ft (11.5 m) of 60-inch (1.52 m) cast film. A partial job like just the hood uses less film. Preparation work such as cleaning and paint correction also changes the cost.

  • Film for a full wrap: about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).
  • Body: hatchback (3 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Vivio wraps by generation

Swipe sideways. Tap a card for the full description.

Subaru Vivio, first generation, factory photo
Factory color shown

1992–1998 Vivio hatchback (first generation)

1992–1998hatchback (3 or 5 doors)129.9 in (3,300 mm)

The first generation Subaru Vivio, produced from 1992 to 1998, often has paint of mixed age. Some panels may be original and others repainted, so a test spot on each panel comes before a full wrap. That test shows whether the vinyl will stick well. A careful check avoids lifting later.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).

Roof, hood, chrome delete and PPF on a Vivio

Smaller jobs on the Subaru Vivio include a partial wrap of the roof, hood, or mirror caps. Vivio chrome delete covers the window trim and badges with black film. Paint protection film (PPF) can be applied as clear film on the front end. These options let you change the look without a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Subaru Vivio: body, cut-outs and film

The Subaru Vivio vinyl wrap follows the simple body of a mini hatchback available with 3 or 5 doors. Its length of 129.9 in (3,300 mm) is modest, so a full wrap uses less film than larger cars. The small size and mostly flat panels make the job straightforward. The 3-door and 5-door styles have the same wrap area.

Vivio wrap ideas start with planning around the tailgate, which has the rear glass set into it. The film ends at the edge of that glass, so the tailgate needs a precise cut-out. You can wrap the tailgate in one piece if you trim carefully around the glass. Door handles and badges may also need cut-outs or removal.

When you work out how much vinyl to wrap a Vivio, only one generation exists, so the figure stays the same for all years from 1992 to 1998. The film estimate is about 38 ft (11.5 m) of 60-inch (1.52 m) cast film for a full wrap. If you choose chrome or patterned film, allow about 48 ft (14.5 m).

Questions about wrapping a Subaru Vivio

How much vinyl does it take to wrap a Subaru Vivio?

A full wrap of a Subaru Vivio takes about 38 ft (11.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, you need about 48 ft (14.5 m). These figures are for the newest body of the only generation.

Can I wrap only the hood or the roof of a Vivio?

Yes, you can wrap only the hood or the roof of a Vivio. The partial wrap options for this car include the roof, hood, and mirror caps. A smaller job uses less film and can be done on its own.

Is a Vivio hard to wrap?

A Vivio is not hard to wrap, but the tailgate with the rear glass in it adds some work. The film must end at the edge of the glass, so that area needs careful trimming. The car's small size of 129.9 in (3,300 mm) makes the rest of the panels easy to handle.

How many generations of the Vivio does this page cover?

This page covers one generation of the Subaru Vivio. The catalog includes the first generation, produced from 1992 to 1998. There are no other generations listed.