Wraps by car

Toyota Belta wrap

The Toyota Belta wrap page covers the first-generation subcompact sedan built from 2005 to 2012. A full vinyl wrap of this car takes about 52 ft (16 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly 10 ft (3 m) to that estimate.

1generations16 mof film for a full wrap

Toyota Belta, first generation, factory photo
Toyota Belta, first generation. Factory color shown.

Toyota Belta wrap colors and ideas

  • Belta black wrap
  • Belta white wrap
  • Belta gray wrap
  • Belta silver wrap
  • Belta red wrap
  • Belta blue wrap
  • Belta green wrap
  • Belta yellow wrap
  • Belta orange wrap
  • Belta purple wrap
  • Belta pink wrap
  • Belta teal wrap
  • Belta brown wrap
  • Belta gold wrap
  • Belta chrome wrap
  • Belta color shift wrap
  • Belta carbon fiber wrap
  • Belta camo and patterned wrap

How much vinyl to wrap a Toyota Belta

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2005–2012sedan (4 doors)169.3 in (4,300 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m)

Belta wrap cost factors

The Belta wrap cost depends on the film type, the condition of the paint, and how much of the car is covered. A full wrap of this 169.3 in (4,300 mm) sedan needs about 52 ft (16 m) of film, while chrome or patterned film raises that to about 62 ft (19 m). Labor for removing trim and working around the four doors also adds to the final bill.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).
  • Body: sedan (4 doors).

Belta wraps by generation

Swipe sideways. Tap a card for the full description.

Toyota Belta, first generation, factory photo
Factory color shown

2005–2012 Belta sedan (first generation)

2005–2012sedan (4 doors)169.3 in (4,300 mm)

The first-generation Toyota Belta was produced from 2005 to 2012 as a four-door sedan in the XP90 series. On a car of these years, panels may be original or repainted, and a test spot comes before a full wrap. Checking for rust or peeling clear coat is part of the prep on this generation.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).

Roof, hood, chrome delete and PPF on a Belta

A partial wrap on the Belta can cover the roof, hood, or mirror caps without using the full 52 ft (16 m) of film. A Belta chrome delete covers the window trim and badges with black film for a cleaner look. Paint protection film (PPF) on the front end is another option to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Toyota Belta: body, cut-outs and film

The Toyota Belta vinyl wrap is sized for one four-door sedan body at 169.3 in (4,300 mm) long. That compact length keeps film waste low on large panels like the roof and hood. The four doors and trunk lid are the main flat areas that take most of the material.

Belta wrap ideas start with the door handles, mirrors, and badges, which are removed or masked for a clean edge. The grille and bumper openings need careful cut-outs around lights and trim. A chrome delete on the window trim and badges is a smaller job that can be done without wrapping the whole car.

How much vinyl to wrap a Belta depends on the single generation in this catalog, so the 52 ft (16 m) figure stays consistent from 2005 to 2012. A sedan body means no extra film for a hatch or wagon. Measuring the car before cutting is still the safe way to confirm the estimate.

Questions about wrapping a Toyota Belta

How much vinyl does it take to wrap a Toyota Belta?

It takes about 52 ft (16 m) of 60-inch (1.52 m) cast film to wrap a Toyota Belta. For chrome or patterned film, plan for about 62 ft (19 m). These figures cover the full exterior of the four-door sedan body.

Can I wrap only the hood or the roof of a Belta?

Yes, you can wrap only the hood or the roof of a Belta. A partial wrap covers those panels without the full 52 ft (16 m) needed for the whole car. Mirror caps are another small area that can be done separately.

Is a Belta hard to wrap?

A Belta is moderately hard to wrap because of its four doors and the small trim around the windows and grille. The 169.3 in (4,300 mm) length is not a problem, but the bumper openings need careful cutting. Removing badges and door handles adds time to the job.

How many generations of the Belta does this page cover?

This page covers one generation of the Toyota Belta, built from 2005 to 2012 as a four-door sedan. It is the XP90 series, the only body style in this catalog.