Wraps by car

Toyota Brevis wrap

The Toyota Brevis wrap page covers the first-generation sedan produced from 2001 to 2007, the only generation in the catalog. A full Toyota Brevis wrap uses about 51 ft (15.5 m) of 60-inch (1.52 m) cast vinyl film. With chrome or patterned film, plan for about 57 ft (17.5 m) of vinyl wrap.

1generations15.5 mof film for a full wrap

Toyota Brevis, first generation, factory photo
Toyota Brevis, first generation. Factory color shown.

Toyota Brevis wrap colors and ideas

  • Brevis black wrap
  • Brevis white wrap
  • Brevis gray wrap
  • Brevis silver wrap
  • Brevis red wrap
  • Brevis blue wrap
  • Brevis green wrap
  • Brevis yellow wrap
  • Brevis orange wrap
  • Brevis purple wrap
  • Brevis pink wrap
  • Brevis teal wrap
  • Brevis brown wrap
  • Brevis gold wrap
  • Brevis chrome wrap
  • Brevis color shift wrap
  • Brevis carbon fiber wrap
  • Brevis camo and patterned wrap

How much vinyl to wrap a Toyota Brevis

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2001–2007sedan (4 doors)179.1 in (4,550 mm)about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m)

Brevis wrap cost factors

Brevis wrap cost depends on the amount of film, the labor for panel removal, and the condition of the 2001–2007 paint. A full wrap needs about 51 ft (15.5 m) of cast film, or about 57 ft (17.5 m) with chrome or patterned film. More cut-outs around trim and badges add labor. Paint correction before wrapping also affects the total.

  • Film for a full wrap: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).
  • Body: sedan (4 doors).

Brevis wraps by generation

Swipe sideways. Tap a card for the full description.

Toyota Brevis, first generation, factory photo
Factory color shown

2001–2007 Brevis sedan (first generation)

2001–2007sedan (4 doors)179.1 in (4,550 mm)

The first-generation Toyota Brevis from 2001 to 2007 may have original or repainted panels after years of use. A test spot of vinyl on a small area shows whether the paint can hold the film. Panels with failing clear coat need repair before wrapping. The age of the paint is a key point for planning a full wrap.

Film: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).

Roof, hood, chrome delete and PPF on a Brevis

Partial wrap options for the Brevis include the roof, hood, or mirror caps as separate jobs. A Brevis chrome delete covers the window trim and badges with black film. Paint protection film (PPF) can be applied as a clear film on the front end. These smaller jobs use less film than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Toyota Brevis: body, cut-outs and film

A Toyota Brevis vinyl wrap covers a mid-size four-door sedan with a length of 179.1 in (4,550 mm). The single body style has four doors, a trunk lid, and standard sedan panels. The size means every panel is manageable, but the roof and hood are large single pieces. The wrap requires careful layout because the car has no hatch or wagon option.

Brevis wrap ideas start with the sedan's trim, badges, door handles, and mirrors. These parts are removed or have cut-outs so the film tucks cleanly around edges. Window trim and badges are typical areas for a chrome delete with black film. The front and rear bumpers also need relief cuts for sensors or tow hook covers.

How much vinyl to wrap a Brevis stays the same across the 2001–2007 run because only one generation exists. There are no earlier or later body styles to compare. The same measurements work for every Brevis, so the film estimate does not change. The only variation comes from the film type, with chrome or patterned film needing extra material.

Questions about wrapping a Toyota Brevis

How much vinyl does it take to wrap a Toyota Brevis?

Yes, a Toyota Brevis needs about 51 ft (15.5 m) of 60-inch (1.52 m) cast film for a full wrap. With chrome or patterned film, the amount is about 57 ft (17.5 m). The sedan body has no complex curves that add extra material.

Can I wrap only the hood or the roof of a Brevis?

Yes, you can wrap only the hood or the roof of a Brevis. Other partial jobs include mirror caps, chrome delete on window trim and badges, and paint protection film on the front end.

Is a Brevis hard to wrap?

A Brevis is not especially hard to wrap, but the four doors, trunk, and many trim pieces add work. The car is a mid-size sedan, so the roof and hood are large single panels. Chrome trim and badges must be removed or cut around carefully.

How many generations of the Brevis does this page cover?

This page covers one generation of the Brevis, the first generation from 2001 to 2007. There are no other generations in the catalog.