Wraps by car

Toyota Progres wrap

The Toyota Progres wrap page covers the full-size first-generation sedan (1998–2007). A vinyl wrap for the complete body takes about 51 ft (15.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly 20 percent and uses about 62 ft (19 m).

1generations15.5 mof film for a full wrap

Toyota Progres, first generation, factory photo
Toyota Progres, first generation. Factory color shown.

Toyota Progres wrap colors and ideas

  • Progres black wrap
  • Progres white wrap
  • Progres gray wrap
  • Progres silver wrap
  • Progres red wrap
  • Progres blue wrap
  • Progres green wrap
  • Progres yellow wrap
  • Progres orange wrap
  • Progres purple wrap
  • Progres pink wrap
  • Progres teal wrap
  • Progres brown wrap
  • Progres gold wrap
  • Progres chrome wrap
  • Progres color shift wrap
  • Progres carbon fiber wrap
  • Progres camo and patterned wrap

How much vinyl to wrap a Toyota Progres

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1998–2007sedan (4 doors)177.2 in (4,500 mm)about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m)

Progres wrap cost factors

Progres wrap cost reflects the sedan's 177.2 in (4,500 mm) length and the condition of a 1998–2007 car. A full wrap needs about 51 ft (15.5 m) of cast film, so material volume sets the base. Repainted panels or rust around the arches require more prep before the film can stick. Removing handles, trim and badges adds labor hours to the estimate.

  • Film for a full wrap: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).
  • Body: sedan (4 doors).

Progres wraps by generation

Swipe sideways. Tap a card for the full description.

Toyota Progres, first generation, factory photo
Factory color shown

1998–2007 Progres sedan (first generation)

1998–2007sedan (4 doors)177.2 in (4,500 mm)

The first-generation Toyota Progres from 1998 through 2007 asks the installer to inspect paint age before quoting. Panels may be original or resprayed, and a test spot shows whether film will lift old clear coat. A full wrap of this G10 sedan still takes the same 51 ft (15.5 m) of 60-inch (1.52 m) cast film. The installer can use the test spot to decide on primer for weak areas.

Film: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).

Roof, hood, chrome delete and PPF on a Progres

A Progres chrome delete covers the window trim and badges in black film without wrapping the whole car. The same job can be done as a partial wrap on the roof, hood or mirror caps at lower material use than a full wrap. Paint protection film (PPF) offers a clear film on the front end to guard against stone chips. These smaller jobs are a way to change one area or protect high-wear surfaces.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Toyota Progres: body, cut-outs and film

The Toyota Progres vinyl wrap works with one sedan body style over a 177.2 in (4,500 mm) length. Four doors and a class-leading cabin mean more flat panels and less roof area than on a wagon. The wrap technician can lay film across the doors without long roof stretches. A clean G10 sedan needs no extra allowance for a tailgate or rear wiper.

Progres wrap ideas start with the door handles and mirror caps because they are small and removable. The front bumper has wide lower openings that need cut-outs around fog lights and grille bars. The side moldings and window trim are best removed so the film can tuck behind them. Badges come off for a smooth finish and are replaced after the wrap.

To judge how much vinyl to wrap a Progres, count the same 1998–2007 first generation. The body was not reskinned, so a full wrap of 51 ft (15.5 m) covers every year. Early cars may have rust on fender lips, which adds prep work but no film. The only trim change is minor for the grille, so the G10 order is unlike a multi-generation model.

Questions about wrapping a Toyota Progres

How much vinyl does it take to wrap a Toyota Progres?

A full wrap of a Toyota Progres takes about 51 ft (15.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for roughly 62 ft (19 m) because of pattern matching and overlap.

Can I wrap only the hood or the roof of a Progres?

Yes, a partial wrap on the hood or the roof of a Progres is a standard job. The same option includes mirror caps, while a chrome delete covers window trim and badges.

Is a Progres hard to wrap?

The Progres is a large sedan at 177.2 in (4,500 mm), so a wrap takes more film and more time than a small hatchback. The doors, trunk and bumpers are not especially curved, but the front bumper has several openings that need cut-outs. Removing the side moldings and badges adds labor before the film goes on.

How many generations of the Progres does this page cover?

This page covers one generation of the Progres, the first-generation G10 sedan built from 1998 to 2007.