Wraps by car

Toyota Scepter wrap

The Toyota Scepter wrap covers this full-size car with cast vinyl film sized to its body. The Scepter was produced from 1992 to 1996 in one generation. A full wrap of the newest body takes about 51 ft (15.5 m) of film for the coupe.

1generations15.5 mof film for a full wrap

Toyota Scepter, first generation, factory photo
Toyota Scepter, first generation. Factory color shown.

Toyota Scepter wrap colors and ideas

  • Scepter black wrap
  • Scepter white wrap
  • Scepter gray wrap
  • Scepter silver wrap
  • Scepter red wrap
  • Scepter blue wrap
  • Scepter green wrap
  • Scepter yellow wrap
  • Scepter orange wrap
  • Scepter purple wrap
  • Scepter pink wrap
  • Scepter teal wrap
  • Scepter brown wrap
  • Scepter gold wrap
  • Scepter chrome wrap
  • Scepter color shift wrap
  • Scepter carbon fiber wrap
  • Scepter camo and patterned wrap

How much vinyl to wrap a Toyota Scepter

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1992–1996coupe, sedan, wagon (2 or 4 or 5 doors)188.2 in (4,780 mm) to 189.8 in (4,820 mm)about 51 ft (15.5 m) for the coupe to 57 ft (17.5 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 74 ft (22.5 m)

Scepter wrap cost factors

Scepter wrap cost depends on the body style, the film type, and the amount of surface area. A wagon uses roughly 6 ft (1.8 m) more film than a coupe, so material cost is higher. Chrome or patterned film runs up to about 74 ft (22.5 m), which adds to material and labor. The number of cutouts, like around the tailgate glass, also influences the final cost.

  • Film for a full wrap: about 51 ft (15.5 m) for the coupe to 57 ft (17.5 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 74 ft (22.5 m).
  • Body: coupe, sedan, wagon (2 or 4 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Scepter wraps by generation

Swipe sideways. Tap a card for the full description.

Toyota Scepter, first generation, factory photo
Factory color shown

1992–1996 Scepter coupe, sedan, wagon (first generation)

1992–1996coupe, sedan, wagon (2 or 4 or 5 doors)188.2 in (4,780 mm) to 189.8 in (4,820 mm)

The first generation Toyota Scepter came as a coupe, sedan, and wagon from 1992 to 1996. The body style decides the panel plan and the film amount for a wrap. The coupe has the fewest large panels, while the wagon adds a tall tailgate and a long roof. All three share the same front end design, so the bumper and hood cuts are similar.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 51 ft (15.5 m) for the coupe to 57 ft (17.5 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 74 ft (22.5 m).

Roof, hood, chrome delete and PPF on a Scepter

Partial wrap options for the Toyota Scepter include the roof, hood, and mirror caps. A Scepter chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. These smaller jobs use less film and leave the original color visible on most panels.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Toyota Scepter: body, cut-outs and film

A Toyota Scepter vinyl wrap is planned around its body style and exterior size. The coupe needs the least film and the wagon needs the most because of its longer roof and tall tailgate. The sedan sits in between, with a simpler roof and trunk than the wagon. All versions measure close to 188 to 190 inches, so panel sizes stay consistent across the lineup.

Scepter wrap ideas often work around the tailgate with the rear glass set into it. The film ends at the edge of that glass, so installers cut cleanly along the opening. The coupe and sedan have conventional trunk lids, which are easier to cover in one piece. Chrome trim and badges are separate small jobs that can be wrapped in black or left as they are.

Knowing how much vinyl to wrap a Scepter starts with its single generation body styles. A coupe takes about 51 ft (15.5 m) of 60-inch film, while the wagon takes about 57 ft (17.5 m). The difference comes from the wagon's extra roof area and its taller rear panels. Sedan estimators fall between those two figures, depending on whether it has a sunroof or a spoiler.

Questions about wrapping a Toyota Scepter

How much vinyl does it take to wrap a Toyota Scepter?

A full Toyota Scepter wrap takes about 51 ft (15.5 m) of 60-inch cast film for the coupe. The wagon needs about 57 ft (17.5 m) because of its larger rear body. These figures assume a single color with normal waste and no roof rack. Chrome or patterned film can require up to about 74 ft (22.5 m) due to matching patterns.

Which Scepter body takes more film?

The wagon body of the Toyota Scepter takes more film than the coupe or sedan. The coupe needs about 51 ft (15.5 m), while the wagon needs about 57 ft (17.5 m). The extra film covers the wagon's longer roof and taller tailgate. The sedan falls between the two, depending on its exact trim and options.

Can I wrap only the hood or the roof of a Scepter?

Yes, you can wrap only the hood or the roof of a Scepter as a partial job. The roof is a common single panel, and the hood is also done alone. Mirror caps are another small area that can be wrapped without doing the whole car. A partial wrap uses less film and can match or contrast with the original paint.

Is a Scepter hard to wrap?

A Toyota Scepter is moderately hard to wrap because of its size and the tailgate glass. The rear hatch on the wagon has the glass set into it, so the film must be cut carefully at that edge. The car is nearly 190 inches long, which means large roof and side panels. Otherwise the body lines are straightforward, so an experienced installer handles it without unusual difficulty.