Wraps by car

Toyota Spade wrap

A Toyota Spade wrap covers the compact minivan with vinyl film, and the catalog holds one generation of this car. The Spade was built from 2012 to 2020 and comes as a three-door van. A full wrap of the newest body takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film.

1generations18.5 mof film for a full wrap

Toyota Spade, first generation, factory photo
Toyota Spade, first generation. Factory color shown.

Toyota Spade wrap colors and ideas

  • Spade black wrap
  • Spade white wrap
  • Spade gray wrap
  • Spade silver wrap
  • Spade red wrap
  • Spade blue wrap
  • Spade green wrap
  • Spade yellow wrap
  • Spade orange wrap
  • Spade purple wrap
  • Spade pink wrap
  • Spade teal wrap
  • Spade brown wrap
  • Spade gold wrap
  • Spade chrome wrap
  • Spade color shift wrap
  • Spade carbon fiber wrap
  • Spade camo and patterned wrap

How much vinyl to wrap a Toyota Spade

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2012–2020van (3 doors)157.1 in (3,990 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Spade wrap cost factors

Spade wrap cost depends on how much film the tall body needs and how many panels you cover. A full wrap uses about 61 ft (18.5 m) of 60-inch (1.52 m) cast film, while chrome or patterned film adds about 69 ft (21 m). The sliding door tracks and two long doors also add labor, because the film must be cut around them.

  • Film for a full wrap: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: van (3 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.
  • Two long side doors: each door is one large piece of film.

Spade wraps by generation

Swipe sideways. Tap a card for the full description.

Toyota Spade, first generation, factory photo
Factory color shown

2012–2020 Spade van (first generation)

2012–2020van (3 doors)157.1 in (3,990 mm)

The first generation Toyota Spade, built from 2012 to 2020, has sliding side doors that shape the wrap job. The door tracks stay bare, so the installer cuts the film along those lines. This keeps the doors sliding freely and gives the wrap a clean edge.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Two long side doors: each door is one large piece of film.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Spade

A partial wrap on a Toyota Spade covers just the roof, hood, or mirror caps. For a chrome delete, the window trim and badges are wrapped in black film. Paint protection film (PPF) is another option: clear film is applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Toyota Spade: body, cut-outs and film

A Toyota Spade vinyl wrap has to follow a tall, boxy body that is 157.1 in (3,990 mm) long. The three-door van has a large roof and flat side panels, so the film is cut into big pieces. Because the body is slab-sided, a color change wrap shows off the clean shape without many curves to fight.

Spade wrap ideas start with the two long side doors, each covered by one large piece of film. The sliding door tracks stay bare, and the film is cut along them so the doors still open cleanly. If you want a chrome delete, the window trim and badges are covered with black film.

When you count how much vinyl to wrap a Spade, the single generation from 2012 to 2020 keeps the math simple. Every Spade has the same 157.1 in (3,990 mm) body length and the same three-door layout. You do not need to adjust the film plan for different generations, since only one body was made.

Questions about wrapping a Toyota Spade

How much vinyl does it take to wrap a Toyota Spade?

A Toyota Spade takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a full wrap. That figure is for the newest body, and it covers the three-door van without extra pieces for chrome or patterns.

Are the sliding doors of a Spade wrapped?

Yes, the sliding doors of a Spade are wrapped, but the tracks stay bare. The film is cut along the door tracks, and each long side door is covered with one large piece.

Can I wrap only the hood or the roof of a Spade?

Yes, you can wrap only the hood or the roof of a Spade. A partial wrap on this van typically covers the roof, hood, or mirror caps, and it uses less film than a full wrap.

Is a Spade hard to wrap?

A Spade is moderately hard to wrap because of the sliding door tracks and the two long side doors. The tracks must stay bare, so the film is cut along them, and each door is one large piece that needs careful handling.