Wraps by car

Dodge Stealth wrap

The Dodge Stealth wrap page covers the first generation produced from 1990 to 1996. A vinyl wrap on this sports car takes about 49 ft (15 m) of 60-inch (1.52 m) cast film for a full color change. Buyers who choose chrome or patterned film need roughly 56 ft (17 m) for the same coverage.

1generations15 mof film for a full wrap

Dodge Stealth, first generation, factory photo
Dodge Stealth, first generation. Factory color shown.

Dodge Stealth wrap colors and ideas

  • Stealth black wrap
  • Stealth white wrap
  • Stealth gray wrap
  • Stealth silver wrap
  • Stealth red wrap
  • Stealth blue wrap
  • Stealth green wrap
  • Stealth yellow wrap
  • Stealth orange wrap
  • Stealth purple wrap
  • Stealth pink wrap
  • Stealth teal wrap
  • Stealth brown wrap
  • Stealth gold wrap
  • Stealth chrome wrap
  • Stealth color shift wrap
  • Stealth carbon fiber wrap
  • Stealth camo and patterned wrap

How much vinyl to wrap a Dodge Stealth

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1990–1996coupe (2 doors)179.5 in (4,560 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)

Stealth wrap cost factors

Stealth wrap cost is controlled by the amount of film and the labour needed for a 179.5 in (4,560 mm) coupe. A full wrap uses about 49 ft (15 m) of 60-inch (1.52 m) cast film, or 56 ft (17 m) for chrome or patterned film. The two long doors add time and skill because each one is a single large piece. Removing mirrors and handles, then wrapping the bumpers, also changes the final cost.

  • Film for a full wrap: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Stealth wraps by generation

Swipe sideways. Tap a card for the full description.

Dodge Stealth, first generation, factory photo
Factory color shown

1990–1996 Stealth coupe (first generation)

1990–1996coupe (2 doors)179.5 in (4,560 mm)

The first generation Dodge Stealth from 1990 to 1996 is a two-door coupe with a 179.5 in (4,560 mm) body. Paint age on a car of these years may be original or repainted, and a test spot comes before a full wrap. The body style stayed the same through the whole run, so film patterns repeat from one car to the next. A full wrap of this generation takes about 49 ft (15 m) of 60-inch (1.52 m) cast film.

Two long side doors: each door is one large piece of film.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Roof, hood, chrome delete and PPF on a Stealth

Partial wrap jobs on a Dodge Stealth can cover the roof, hood, or mirror caps as separate panels. A chrome delete for window trim and badges uses black film to cover the bright parts. Paint protection film (PPF) is often applied to the front end as a clear film that keeps stone chips away. These smaller jobs use less film than a full wrap and can be done one section at a time.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Dodge Stealth: body, cut-outs and film

Dodge Stealth vinyl wrap coverage is shaped by the two-door coupe body that measures 179.5 in (4,560 mm) in length. The long doors are the largest single panels on the car and each one is wrapped as one piece. The roof and hood are moderate panels that use straight sections of film. The rear bumper and deck lid need careful trimming around the tail lights and spoiler.

Stealth wrap ideas start with the two long side doors because each door is one large piece of film. Door handles, mirrors, and the antenna need cut-outs or removal before the film goes on. The front bumper has air intakes that require relief cuts and careful heating. The rear hatch area is simpler but the glass edge must be tucked cleanly.

How much vinyl to wrap a Stealth depends on the condition of body panels from these production years. The first generation ran from 1990 to 1996 and every coupe uses the same body shell. A car with original or repainted panels can still be wrapped after a test spot checks adhesion. Film estimators use the same 49 ft (15 m) figure for every Stealth of this generation.

Questions about wrapping a Dodge Stealth

How much vinyl does it take to wrap a Dodge Stealth?

A Dodge Stealth full wrap takes about 49 ft (15 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film the estimate rises to about 56 ft (17 m).

Can I wrap only the hood or the roof of a Stealth?

Yes, you can wrap only the hood or the roof of a Stealth. Partial wrap jobs cover the roof, hood, or mirror caps, and a chrome delete covers the window trim and badges.

Is a Stealth hard to wrap?

A Stealth is not a hard car to wrap, but the two long side doors are the main challenge because each door is one large piece of film. The body length of 179.5 in (4,560 mm) and the front bumper intakes also add work.

How many generations of the Stealth does this page cover?

This page covers one generation of the Dodge Stealth, the first generation produced from 1990 to 1996.