Wraps by car

DongFeng MPV wrap

The DongFeng MPV wrap section covers the first-generation 2007–2009 minivan, the only generation in this catalog. A full wrap of its van body takes about 70 ft (21.5 m) of 60-inch (1.52 m) cast vinyl wrap. For chrome or patterned film, plan on about 84 ft (25.5 m) because the pattern needs extra material. The page explains what makes this boxy minivan different to wrap from a modern crossover.

1generations21.5 mof film for a full wrap

DongFeng MPV, first generation, factory photo
DongFeng MPV, first generation. Factory color shown.

DongFeng MPV wrap colors and ideas

  • DongFeng MPV black wrap
  • DongFeng MPV white wrap
  • DongFeng MPV gray wrap
  • DongFeng MPV silver wrap
  • DongFeng MPV red wrap
  • DongFeng MPV blue wrap
  • DongFeng MPV green wrap
  • DongFeng MPV yellow wrap
  • DongFeng MPV orange wrap
  • DongFeng MPV purple wrap
  • DongFeng MPV pink wrap
  • DongFeng MPV teal wrap
  • DongFeng MPV brown wrap
  • DongFeng MPV gold wrap
  • DongFeng MPV chrome wrap
  • DongFeng MPV color shift wrap
  • DongFeng MPV carbon fiber wrap
  • DongFeng MPV camo and patterned wrap

How much vinyl to wrap a DongFeng MPV

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2007–2009van (4 doors)198.8 in (5,050 mm)about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 84 ft (25.5 m)

DongFeng MPV wrap cost factors

A DongFeng MPV wrap cost depends on the size of the panels, the condition of the paint, and how much of the van is covered. This first-generation van is 198.8 in (5,050 mm) long, so the body area is larger than on a compact car. The sliding doors add time because the film must be trimmed around the tracks, but the flat sides keep the labor lower than on a curved body. The type of film also changes the cost, because a full wrap needs about 70 ft (21.5 m) of 60-inch (1.52 m) cast vinyl wrap.

  • Film for a full wrap: about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 84 ft (25.5 m).
  • Body: van (4 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.

DongFeng MPV wraps by generation

Swipe sideways. Tap a card for the full description.

DongFeng MPV, first generation, factory photo
Factory color shown

2007–2009 DongFeng MPV van (first generation)

2007–2009van (4 doors)198.8 in (5,050 mm)

The first-generation DongFeng MPV from 2007–2009 has sliding side doors that define how the vinyl wrap is installed. Those doors slide in external tracks on the body, and the tracks stay bare because film would peel or jam the rollers. The installer cuts the film along the upper and lower edges of each track so the door opens freely. The rest of the door panel is wrapped, and the cut line is hidden by the track itself.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 84 ft (25.5 m).

Roof, hood, chrome delete and PPF on a DongFeng MPV

A partial wrap on a DongFeng MPV covers smaller areas like the roof, hood, or mirror caps, and it uses less film than a full wrap. A chrome delete covers the window trim and badges with black film instead of wrapping the whole body. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. These jobs are a way to change the look or protect the van without committing to a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a DongFeng MPV: body, cut-outs and film

A DongFeng MPV vinyl wrap has to cover a long, flat-sided van body, and the 198.8 in (5,050 mm) length means no standard kit fits. The sliding side doors are the main body feature, and the film must be trimmed along the door tracks. The tall, vertical panels take wide sheets of film but are easy to stretch and lay flat. The roof is large and often left unwrapped on a full job, which reduces the film used.

DongFeng MPV wrap ideas often focus on the sliding doors, which stay fully wrapped while the door tracks remain bare. The front and rear bumpers wrap easiest when left on the car, but the door handles and mirrors need careful knife work. The badges and the window trim are removed for a clean edge or covered during a chrome delete. The film is cut along the lower edge of the door tracks so the doors still open without scraping.

How much vinyl to wrap a DongFeng MPV depends on the generation, and this catalog has only the first generation from 2007–2009. That body is 198.8 in (5,050 mm) long, so a full wrap uses about 70 ft (21.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, the estimate goes up to about 84 ft (25.5 m) for the same body. The sliding door tracks do not change the total, because the doors themselves are still fully covered.

Questions about wrapping a DongFeng MPV

How much vinyl does it take to wrap a DongFeng MPV?

A full wrap of a DongFeng MPV takes about 70 ft (21.5 m) of 60-inch (1.52 m) cast vinyl film. If you choose chrome or patterned film, you need about 84 ft (25.5 m) for the same first-generation van body. The extra material on patterned film is for matching the pattern across panels and around the sliding door tracks.

Are the sliding doors of a DongFeng MPV wrapped?

Yes, the sliding doors of a DongFeng MPV are wrapped, but the door tracks stay bare. The film is cut along the edges of each track so the door slides without touching the vinyl. The tracks are part of the body and are left exposed, which gives a clean look and prevents peeling.

Can I wrap only the hood or the roof of a DongFeng MPV?

Yes, you can wrap only the hood or the roof of a DongFeng MPV. A partial wrap often covers the roof, hood, or mirror caps as a single job. You can also choose a chrome delete for the window trim and badges, or paint protection film (PPF) on the front end. These smaller jobs use less film and take less time than a full wrap.

Is a DongFeng MPV hard to wrap?

Yes, a DongFeng MPV is harder to wrap than a small car because it is 198.8 in (5,050 mm) long and the body panels are large. The sliding side doors add work, since the film must be cut accurately along the door tracks. The flat sides and roof help, but the overall size means more lifting and more seams. A first-generation van like this takes more time and care than a sedan of the same era.