Wraps by car

Lincoln Mark III wrap

This page covers the Lincoln Mark III from 1968 to 1971, its single generation listed here, and the vinyl wrap film its coupe body takes. The Mark III is a large luxury two-door car that measures 216.1 in (5,489 mm) in length. A complete wrap calls for about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. With chrome or patterned film, a set needs about 76 ft (23 m).

1generations17.5 mof film for a full wrap

Lincoln Mark III, first generation, factory photo
Lincoln Mark III, first generation. Factory color shown.

Lincoln Mark III wrap colors and ideas

  • Mark III black wrap
  • Mark III white wrap
  • Mark III gray wrap
  • Mark III silver wrap
  • Mark III red wrap
  • Mark III blue wrap
  • Mark III green wrap
  • Mark III yellow wrap
  • Mark III orange wrap
  • Mark III purple wrap
  • Mark III pink wrap
  • Mark III teal wrap
  • Mark III brown wrap
  • Mark III gold wrap
  • Mark III chrome wrap
  • Mark III color shift wrap
  • Mark III carbon fiber wrap
  • Mark III camo and patterned wrap

How much vinyl to wrap a Lincoln Mark III

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1968–1971coupe (2 doors)216.1 in (5,489 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m)

Mark III wrap cost factors

Mark III wrap cost depends on the condition of the paint, the number of cut-outs around trim, and the film type chosen. This car has a large panel area, so a full wrap uses about 57 ft (17.5 m) of 60-inch (1.52 m) cast film, or more with chrome or patterned film. If the car needs paint correction before wrapping or if the chrome is heavily pitted, prep time adds to the labor. Removing the wheel arch moldings and the vinyl roof trim before wrapping also changes the work involved.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Mark III wraps by generation

Swipe sideways. Tap a card for the full description.

Lincoln Mark III, first generation, factory photo
Factory color shown

1968–1971 Mark III coupe (first generation)

1968–1971coupe (2 doors)216.1 in (5,489 mm)

The first generation of the Lincoln Mark III, built from 1968 through 1971, is the only generation shown on this page. These cars may still have their original paint or a respray from decades ago, so a wrap installer must check adhesion with a test spot before a full wrap. Original single-stage paint can be fragile, while repainted panels may have clearcoat failure that needs correction. A test spot shows how the film releases and whether the surface is sound.

Two long side doors: each door is one large piece of film.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).

Roof, hood, chrome delete and PPF on a Mark III

A partial wrap on a Lincoln Mark III can cover the roof, the hood, or the mirror caps without wrapping the whole car. A chrome delete on this car focuses on the window trim and the badges, since those bright pieces are easy to isolate. Paint protection film (PPF) as a clear film can cover the front end, including the leading edge of the hood and the front bumper areas. These smaller jobs use less film than a full wrap and can be planned in sections.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Lincoln Mark III: body, cut-outs and film

A Lincoln Mark III vinyl wrap involves one large coupe body with no rear doors, so the side panels are long and unbroken except for the wheel arches. Each of the two long side doors is one large piece of film, which means clean, straight seams can be placed along the door cut lines. The overall length of 216.1 in (5,489 mm) puts this car close to full-size sedans of its era in terms of surface area. Expect to work around the deep side sculpting and the wide lower rocker panels.

Mark III wrap ideas often include two-tone layouts that use the upper body accent line or a color on the lower rockers. The front bumper on this car is a heavy chrome unit, and the grille and headlight surrounds continue that bright trim theme. Window trim, wheel arch moldings, and badges can be covered for a chrome delete, but their shapes require careful inlay. The vinyl roof section on many Mark IIIs is a textured area that changes how film lays down.

For someone counting film, how much vinyl to wrap a Mark III stays the same across 1968–1971 because the body shell did not change between model years. This page lists only the first generation, so there is no earlier or later body to compare. The only practical difference is paint condition: a car that has been repainted may have tape lines or overspray that a test spot will reveal before a full wrap. Plan the same film set for any year of this generation.

Questions about wrapping a Lincoln Mark III

How much vinyl does it take to wrap a Lincoln Mark III?

A full wrap of a Lincoln Mark III takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, the film estimate rises to about 76 ft (23 m). These figures come from the single generation listed on this page, with its 216.1 in (5,489 mm) length. Add a little extra for waste around the long side doors and the bumper cut-outs.

Can I wrap only the hood or the roof of a Mark III?

Yes, you can wrap only the hood or the roof of a Mark III. A partial wrap can also cover the mirror caps, and a chrome delete can cover only the window trim and badges. Paint protection film can be applied as a clear film on the front end. These smaller jobs use less film than a full wrap and can be planned without touching the rest of the car.

Is a Mark III hard to wrap?

A Mark III is moderately hard to wrap because the two long side doors each need one large piece of film, which requires careful handling. The overall length of 216.1 in (5,489 mm) means large panels, and the deep chrome trim around the windows and rockers calls for precise cutting. If the car has original paint or old repaint, a test spot is needed before the wrap. The vinyl roof section, if present, adds another surface to plan around.

How many generations of the Mark III does this page cover?

This page covers one generation of the Lincoln Mark III, which is the first generation built from 1968 to 1971. No other generations are listed in the catalog for this model. The car is a luxury coupe with two doors and a body length of 216.1 in (5,489 mm). All wrap film estimates on this page refer to that generation.