Wraps by car

Nissan Exa wrap

The Nissan Exa wrap covers this one-generation targa coupe produced from 1986 to 1990. A full vinyl wrap on the 166.5 in (4,230 mm) body uses about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. The car is known under the N13 code, and its open top is a key area for any install.

1generations13.5 mof film for a full wrap

Nissan Exa, first generation, factory photo
Nissan Exa, first generation. Factory color shown.

Nissan Exa wrap colors and ideas

  • Exa black wrap
  • Exa white wrap
  • Exa gray wrap
  • Exa silver wrap
  • Exa red wrap
  • Exa blue wrap
  • Exa green wrap
  • Exa yellow wrap
  • Exa orange wrap
  • Exa purple wrap
  • Exa pink wrap
  • Exa teal wrap
  • Exa brown wrap
  • Exa gold wrap
  • Exa chrome wrap
  • Exa color shift wrap
  • Exa carbon fiber wrap
  • Exa camo and patterned wrap

How much vinyl to wrap a Nissan Exa

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1986–1990targa (3 doors)166.5 in (4,230 mm)about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 49 ft (15 m)

Exa wrap cost factors

The Exa wrap cost depends on the film, the roof type and how much of the car is covered. A full wrap uses about 44 ft (13.5 m) of 60-inch (1.52 m) cast film, while chrome or patterned film needs about 49 ft (15 m). Paint protection film on the front end costs less than a full color change wrap because it covers less area. The targa top adds time if there are separate panels to wrap, so a folding hard top can raise the total.

  • Film for a full wrap: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 49 ft (15 m).
  • Body: targa (3 doors).
  • Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Exa wraps by generation

Swipe sideways. Tap a card for the full description.

Nissan Exa, first generation, factory photo
Factory color shown

1986–1990 Exa targa (first generation)

1986–1990targa (3 doors)166.5 in (4,230 mm)

The first generation Nissan Exa is a targa with three doors, built from 1986 to 1990. In a wrap, a fabric top is not wrapped and the film ends where it begins, while a folding hard top is wrapped as panels of its own. The body is 166.5 in (4,230 mm) long, and the film estimate of about 44 ft (13.5 m) covers the whole car. The N13 code is the one body an installer will see for this model.

Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 49 ft (15 m).

Roof, hood, chrome delete and PPF on an Exa

The Exa chrome delete covers window trim and badges with black film for a subtle change. A partial wrap on the hood, mirror caps or rear deck is a smaller job that changes the car without a full roll of film. Paint protection film as a clear film on the front end guards against stone chips. The targa panels can also be wrapped on their own to change the look above the beltline.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Nissan Exa: body, cut-outs and film

The Nissan Exa vinyl wrap follows the single targa body style with three doors. The compact 166.5 in (4,230 mm) length keeps film use close to 44 ft (13.5 m) for a full color change wrap. Its short rear deck and small hood mean fewer large panels than on a sedan. The open top changes how the upper half of the car is wrapped, so layout matters more than on a fixed roof car.

Exa wrap ideas start with the removable roof panels and the trim around the side windows. The targa body means a fabric top is not wrapped and the film ends where it begins, while a folding hard top is wrapped as panels of its own. Window trims and badges are small pieces that need careful cut-outs, and the mirrors come off for a clean edge. The rear deck and the hood are the most direct panels for a partial change.

How much vinyl to wrap an Exa depends on the roof type and the job size. A full wrap of this first and only generation takes about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film needs about 49 ft (15 m) because the pattern must be matched across panels. The N13 body was made for only five years, so there is no older or newer shape to compare for film use.

Questions about wrapping a Nissan Exa

How much vinyl does it take to wrap a Nissan Exa?

It takes about 44 ft (13.5 m) of 60-inch (1.52 m) cast film to wrap a Nissan Exa. Chrome or patterned film needs about 49 ft (15 m) because matching the pattern across panels uses extra material. The figure is based on the first generation body with three doors and a targa top.

Is the top of an Exa wrapped?

Yes or no, depending on the top of the Exa. A fabric top is not wrapped and the film ends where it begins, so the soft material stays uncovered. A folding hard top is wrapped as panels of its own, so the film follows each removable section. The body around the top is always wrapped as normal.

Can I wrap only the hood or the roof of an Exa?

Yes, a partial wrap for an Exa can cover only the hood or the rear deck, and a chrome delete covers window trim and badges. Paint protection film is a clear film for the front end that leaves the color visible. The roof on a targa is not a single fixed panel, so a fabric top is left unwrapped and a hard top is done as separate panels.

Is an Exa hard to wrap?

Yes, the Exa is a little harder to wrap than a fixed roof car of the same size. The targa body means a fabric top is not wrapped and the film ends where it begins, or a folding hard top is wrapped as panels of its own. The 166.5 in (4,230 mm) length keeps the car small, but the removable sections add steps for clean edges.