Wraps by car

Nissan Fuga wrap

This page covers the Nissan Fuga wrap in vinyl film for both generations of the full-size sedan. The newest body, sold since 2009, needs about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a full wrap. The first generation, from 2004 to 2009, needs about 52 ft (16 m) of the same film. Chrome or patterned film raises the amount to about 69 ft (21 m) on the newer car and 61 ft (18.5 m) on the older one.

2generations18.5 mof film for a full wrap

Nissan Fuga, second generation, factory photo
Nissan Fuga, second generation. Factory color shown.

Nissan Fuga wrap colors and ideas

  • Fuga black wrap
  • Fuga white wrap
  • Fuga gray wrap
  • Fuga silver wrap
  • Fuga red wrap
  • Fuga blue wrap
  • Fuga green wrap
  • Fuga yellow wrap
  • Fuga orange wrap
  • Fuga purple wrap
  • Fuga pink wrap
  • Fuga teal wrap
  • Fuga brown wrap
  • Fuga gold wrap
  • Fuga chrome wrap
  • Fuga color shift wrap
  • Fuga carbon fiber wrap
  • Fuga camo and patterned wrap

How much vinyl to wrap a Nissan Fuga

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–nowsedan (4 doors)194.1 in (4,930 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)
2004–2009sedan (4 doors)190.6 in (4,840 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Fuga wrap cost factors

Fuga wrap cost depends first on the size of the car and the amount of film, which is about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for the newest body. The price changes with the film brand and type, such as a plain color versus a chrome or patterned film that requires 69 ft (21 m). The number of panels and trim pieces adds labor, and a full wrap of a full-size sedan takes more hours than a partial job. Condition of the paint matters too, because old or repainted panels may need more prep before film can be applied.

  • Film for a full wrap: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: sedan (4 doors).

Fuga wraps by generation

Swipe sideways. Tap a card for the full description.

Nissan Fuga, second generation, factory photo
Factory color shown

2009–now Fuga sedan (second generation)

2009–nowsedan (4 doors)194.1 in (4,930 mm)

The second generation Fuga, sold since 2009 as the Y51, uses a body that is 194.1 in (4,930 mm) long and takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a full color change wrap. Paint age on a car of these years can vary between original and repainted panels, so a test spot on each panel tells how well the film will stick. If the paint is weak or flaking, the installer may need to sand or seal those areas before wrapping. That step adds time to the job but helps the film lie flat and stay down.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Nissan Fuga, first generation, factory photo
Factory color shown

2004–2009 Fuga sedan (first generation)

2004–2009sedan (4 doors)190.6 in (4,840 mm)

The first generation Fuga, sold from 2004 to 2009 as the Y50, is a full-size sedan measuring 190.6 in (4,840 mm) in length. Its smaller body means a full wrap takes about 52 ft (16 m) of 60-inch (1.52 m) cast film for a standard color, less than the newer Y51. The four-door shape has the same major panels as later cars, so the number of pieces is similar, but each panel is slightly shorter. That reduces the film length and can also cut the time needed to trim and finish the edges.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Fuga

A partial wrap on a Fuga can cover the roof, hood and mirror caps while leaving the rest of the paint exposed. Fuga chrome delete means covering the window trim and badges with black film to remove the bright chrome look. Paint protection film (PPF) is a clear film installed on the front bumper, hood, fenders and mirrors to guard against stone chips. These smaller jobs use less material and are a way to change one part of the car without a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Nissan Fuga: body, cut-outs and film

A Nissan Fuga vinyl wrap covers a large four-door sedan body that is 194.1 in (4,930 mm) long in the second generation and 190.6 in (4,840 mm) in the first. The long roof, hood, trunk and tall doors add surface area, so a full wrap uses more film than a compact car. The sedan shape has mostly flat, wrap-friendly panels with few complex curves. This helps a clean install but still calls for careful trimming around the door edges.

Fuga wrap ideas often start with removing or working around the chrome trim on the window frames, grille, door handles and badges. Those parts are not hard to wrap, but they need extra time because each piece is small and the edges must be tucked cleanly. For a color change wrap, the door handles, mirrors and body side moldings can come off to hide the original paint. If you want a sealed look, the installer removes the front and rear bumper covers before wrapping.

To figure out how much vinyl to wrap a Fuga, note that the two generations differ in size and film need. The first generation, sold as the Y50 from 2004 to 2009, uses about 52 ft (16 m) of 60-inch (1.52 m) cast film for a standard color change. The second generation, the Y51 sold since 2009, is longer and takes about 61 ft (18.5 m) of the same film. A chrome or patterned film needs more because the pattern must be matched, raising the figures to 61 ft (18.5 m) for the older car and 69 ft (21 m) for the newer one.

Questions about wrapping a Nissan Fuga

How much vinyl does it take to wrap a Nissan Fuga?

A full wrap of a Nissan Fuga takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film on the newest body. That figure covers a standard color change on the second generation, sold since 2009. A chrome or patterned film needs about 69 ft (21 m) because of the extra film for matching patterns.

Can I wrap only the hood or the roof of a Fuga?

Yes, you can wrap only the hood or the roof of a Fuga as a partial wrap. The partial options for this car include the roof, hood and mirror caps, alone or in combination. You can also do a chrome delete on the window trim and badges, or add clear paint protection film on the front end.

Is a Fuga hard to wrap?

A Fuga is more work than a small car because it is a full-size sedan, 194.1 in (4,930 mm) long in the newest generation, with large flat panels. The wrap installer must handle the long roof, deep bumpers and many trim pieces such as the chrome around the windows. Removing door handles, mirrors and badges adds steps before the film can be applied. The two generations have similar body styles, so the difficulty is about the same for both.

How many generations of the Fuga does this page cover?

This page covers two generations of the Fuga: the first generation sold from 2004 to 2009 and the second generation sold since 2009. Each generation has its own film estimate because the body sizes differ by about 3.5 in (90 mm). The figures for film use both generations in the text above.