Wraps by car

Nissan Teana wrap

The Nissan Teana wrap page covers all three generations of this mid-size sedan, from 2003 to 2020. A full wrap of the newest body takes about 59 ft (18 m) of 60-inch (1.52 m) cast vinyl wrap. For chrome or patterned film, plan on about 69 ft (21 m). The page explains how the film is measured, cut and applied on each version of the car.

3generations18 mof film for a full wrap

Nissan Teana, third generation, factory photo
Nissan Teana, third generation. Factory color shown.

Nissan Teana wrap colors and ideas

  • Teana black wrap
  • Teana white wrap
  • Teana gray wrap
  • Teana silver wrap
  • Teana red wrap
  • Teana blue wrap
  • Teana green wrap
  • Teana yellow wrap
  • Teana orange wrap
  • Teana purple wrap
  • Teana pink wrap
  • Teana teal wrap
  • Teana brown wrap
  • Teana gold wrap
  • Teana chrome wrap
  • Teana color shift wrap
  • Teana carbon fiber wrap
  • Teana camo and patterned wrap

How much vinyl to wrap a Nissan Teana

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2014–2020sedan (4 doors)191.5 in (4,863 mm)about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)
2008–2014sedan (4 doors)190.7 in (4,845 mm) to 190.9 in (4,850 mm)about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)
2003–2008sedan (4 doors)187.8 in (4,770 mm) to 190.7 in (4,845 mm)about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Teana wrap cost factors

Teana wrap cost depends on the size of the car, the condition of the paint, and the number of cut-outs the installer must make. A full wrap on any generation uses about 59 ft (18 m) of 60-inch film, and chrome or patterned film raises that to about 69 ft (21 m). The newest cars with parking sensors and cameras add labor time, because each sensor and lens must be cut around carefully. A car with original paint that is smooth and clean takes less preparation than one with old or repainted panels.

  • Film for a full wrap: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: sedan (4 doors).
  • Some trims have parking sensors in the bumpers: the film is cut around each sensor.
  • Some trims have cameras in the body: the film is cut around each lens.
  • Every trim has fog lamps in the front bumper: cut-outs in the bumper film.

Teana wraps by generation

Swipe sideways. Tap a card for the full description.

Nissan Teana, third generation, factory photo
Factory color shown

2014–2020 Teana sedan (third generation)

2014–2020sedan (4 doors)191.5 in (4,863 mm)

The third-generation Nissan Teana from 2014 to 2020 is 191.5 in (4,863 mm) long, which is typical for a mid-size sedan wrap. The single four-door body style means the installer works on the same set of panels on every car, with no long roof like an SUV. Standard cast film for a full wrap is about 59 ft (18 m), and the same length applies to chrome or patterned film. The long side panels and the deep bumpers are the main areas that use up material on this body.

Some trims have parking sensors in the bumpers: the film is cut around each sensor.

Some trims have cameras in the body: the film is cut around each lens.

Every trim has fog lamps in the front bumper: cut-outs in the bumper film.

Film: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Nissan Teana, second generation, factory photo
Factory color shown

2008–2014 Teana sedan (second generation)

2008–2014sedan (4 doors)190.7 in (4,845 mm) to 190.9 in (4,850 mm)

On the second-generation Teana, some trims have a panoramic glass roof, and glass is not wrapped. The film ends at the roof rails, so the roof stays dark whatever the color of the film. For this reason, a wrap on a car with a glass roof needs less material on the top panel than a car with a steel roof. A sunroof also means the roof film is cut around its opening, which is a detail that affects the layout. The overall film estimate remains about 59 ft (18 m) for the whole car.

Some trims have a panoramic glass roof: glass is not wrapped, and the film ends at the roof rails.

Some trims have a sunroof: the roof film is cut around its opening.

Some trims have cameras in the body: the film is cut around each lens.

Every trim has fog lamps in the front bumper: cut-outs in the bumper film.

Film: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Nissan Teana, first generation, factory photo
Factory color shown

2003–2008 Teana sedan (first generation)

2003–2008sedan (4 doors)187.8 in (4,770 mm) to 190.7 in (4,845 mm)

On a first-generation Teana from 2003 to 2008, the paint may be original or repainted, and a test spot comes before a full wrap. The installer sticks a small piece of film to a panel and checks how the adhesive bonds to the paint. If the paint is cracked or peeling, the film will not lay flat, and the wrap will fail early. For cars of these years, a check of every panel is part of the job before the film is cut.

Film: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Teana

A partial wrap on a Teana is a job smaller than a full color change, such as the roof, hood, or mirror caps. A Teana chrome delete covers the window trim and badges with black film, which changes the look without a full wrap. Paint protection film (PPF) as a clear film on the front end is also a partial job that protects the hood and bumper. These smaller jobs use less film and are done in less time than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Nissan Teana: body, cut-outs and film

A Nissan Teana vinyl wrap is a large job for a four-door sedan, with the newest body measuring 191.5 in (4,863 mm) long. The earlier generations are slightly shorter, from 187.8 in (4,770 mm) to 190.9 in (4,850 mm), so they need a little less film on the side panels. Sedan roofs and hoods have simple curves, but the bumpers and rocker panels take the most time to wrap cleanly. Because the Teana is sold in many markets with different trim levels, a pre-wrap inspection of the exact car prevents surprises on the day of the install.

Teana wrap ideas often focus on the large body panels, but a good installer first looks at the details that add cut-outs. On the newest generation, some trims have parking sensors in the bumpers, and the film is cut around each sensor. Every trim has fog lamps in the front bumper, which means cut-outs in the bumper film. Some trims also have cameras in the body, and the film is cut around each lens so the parking aids keep working.

Anyone counting how much vinyl to wrap a Teana should know that the three generations differ only slightly in size. The first generation is the shortest at 187.8 in (4,770 mm) to 190.7 in (4,845 mm), while the second and third generations are just under 191 in. The second generation was restyled in 2012, but the body shell did not change, so the film estimate stays the same for all L33 cars. Because all generations are mid-size sedans with four doors, a full wrap on any of them uses about 59 ft (18 m) of standard cast film.

Questions about wrapping a Nissan Teana

How much vinyl does it take to wrap a Nissan Teana?

A full wrap of a Nissan Teana takes about 59 ft (18 m) of 60-inch (1.52 m) cast vinyl wrap. For chrome or patterned film, the estimate is about 69 ft (21 m). These figures are for the newest body from 2014 to 2020, and the earlier generations are within a few feet of the same amount.

Can I wrap only the hood or the roof of a Teana?

Yes, a hood or roof wrap on a Teana is a standard partial job. The same applies to mirror caps, a chrome delete on the window trim and badges, or clear paint protection film (PPF) on the front end. These jobs use much less film than a full wrap and focus on one or two panels.

Is a Teana hard to wrap?

A Teana is not hard to wrap, but the newest ones with parking sensors and cameras add work. The film is cut around each sensor and each camera lens, and every trim has fog lamps that need cut-outs in the bumper film. The body is a long mid-size sedan at 191.5 in (4,863 mm), so the side panels take care to lay down without wrinkles.

How many generations of the Teana does this page cover?

This page covers three generations of the Teana, from the first generation of 2003–2008 to the third generation of 2014–2020. The second generation ran from 2008 to 2014, and each body is a four-door sedan. The film estimates for a full wrap are the same for all three.