Wraps by car

Porsche 911 GT2 wrap

A Porsche 911 GT2 wrap page covers all four production generations of this coupe, from 1995 through 2019. A full vinyl wrap of the newest 991 body takes about 49 ft (15 m) of 60-inch (1.52 m) cast film. A chrome or patterned film needs about 7 ft (2 m) more on the same body. The GT2 has always been a two-door coupe, so every generation shares the same basic panel count.

4generations15 mof film for a full wrap

Porsche 911 GT2, fourth generation, factory photo
Porsche 911 GT2, fourth generation. Factory color shown.

Porsche 911 GT2 wrap colors and ideas

  • Porsche 911 GT2 black wrap
  • Porsche 911 GT2 white wrap
  • Porsche 911 GT2 gray wrap
  • Porsche 911 GT2 silver wrap
  • Porsche 911 GT2 red wrap
  • Porsche 911 GT2 blue wrap
  • Porsche 911 GT2 green wrap
  • Porsche 911 GT2 yellow wrap
  • Porsche 911 GT2 orange wrap
  • Porsche 911 GT2 purple wrap
  • Porsche 911 GT2 pink wrap
  • Porsche 911 GT2 teal wrap
  • Porsche 911 GT2 brown wrap
  • Porsche 911 GT2 gold wrap
  • Porsche 911 GT2 chrome wrap
  • Porsche 911 GT2 color shift wrap
  • Porsche 911 GT2 carbon fiber wrap
  • Porsche 911 GT2 camo and patterned wrap

How much vinyl to wrap a Porsche 911 GT2

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2017–2019coupe (2 doors)179.1 in (4,549 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)
2007–2012coupe (2 doors)175.9 in (4,469 mm)about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)
1999–2005coupe (2 doors)175.2 in (4,450 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)
1995–1998coupe (2 doors)167.1 in (4,245 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m)

Porsche 911 GT2 wrap cost factors

Porsche 911 GT2 wrap cost depends on the size of the body, the amount of film, and the labor for the wide rear arches and the long doors. The 997 generation uses about 56 ft (17 m) of film, more than the 991's 49 ft (15 m), so the film material cost is higher. A chrome or patterned film also adds to the cost because those films need more material and more careful alignment. The two-door coupe body has fewer panels than a four-door, but the GT2's wide body still adds labor.

  • Film for a full wrap: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Porsche 911 GT2 wraps by generation

Swipe sideways. Tap a card for the full description.

Porsche 911 GT2, fourth generation, factory photo
Factory color shown

2017–2019 Porsche 911 GT2 coupe (fourth generation)

2017–2019coupe (2 doors)179.1 in (4,549 mm)

The fourth-generation Porsche 911 GT2 coupe is 179.1 in (4,549 mm) long, and its two long side doors each take one large piece of film. A full wrap of this 991 body uses about 49 ft (15 m) of 60-inch (1.52 m) cast film. A chrome or patterned film needs about 56 ft (17 m) because the pattern must be matched across the panels. The coupe body means fewer door gaps and a cleaner look for the wrap.

Two long side doors: each door is one large piece of film.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Porsche 911 GT2, third generation, factory photo
Factory color shown

2007–2012 Porsche 911 GT2 coupe (third generation)

2007–2012coupe (2 doors)175.9 in (4,469 mm)

The third-generation Porsche 911 GT2 was restyled in 2011, so the bumpers and lights changed on the 997 body. Film cut for a 2007–2010 bumper does not fit a 2011–2012 bumper, and the fog lamps moved. Every trim of the 997 has fog lamps in the front bumper, so the bumper film needs cut-outs. The body is tall at 71.9 in (1,825 mm), so the roof is wrapped from a platform.

Two long side doors: each door is one large piece of film.

Every trim has fog lamps in the front bumper: cut-outs in the bumper film.

A tall body (71.9 in (1,825 mm)): the roof is wrapped from a platform.

Film: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Porsche 911 GT2, second generation, factory photo
Factory color shown

1999–2005 Porsche 911 GT2 coupe (second generation)

1999–2005coupe (2 doors)175.2 in (4,450 mm)

The second-generation Porsche 911 GT2 comes from 1999–2005, so the paint may be original or repainted on a car of these years. A test spot with the film on an inconspicuous area is the right step before a full wrap. If the paint is original, the film can still be applied, but older paint may lift if the film is removed later. The 996 body takes about 49 ft (15 m) of 60-inch (1.52 m) cast film.

Two long side doors: each door is one large piece of film.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Porsche 911 GT2, first generation, factory photo
Factory color shown

1995–1998 Porsche 911 GT2 coupe (first generation)

1995–1998coupe (2 doors)167.1 in (4,245 mm)

The first-generation Porsche 911 GT2 coupe is 167.1 in (4,245 mm) long, the shortest of the four generations. Its two long side doors each take one large piece of film, and the car uses about 46 ft (14 m) of 60-inch (1.52 m) cast film. A chrome or patterned film needs about 52 ft (16 m) on this 996 body. The smaller size means less film and fewer panels than the later wide-body cars.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).

Roof, hood, chrome delete and PPF on a Porsche 911 GT2

A partial wrap on a Porsche 911 GT2 covers the roof, hood, and mirror caps, leaving the doors and rear quarters in paint. A chrome delete turns the window trim and badges black with film, and it uses much less material than a full wrap. Paint protection film (PPF) is clear film on the front end of the GT2, and it protects the hood, bumper, and mirrors from stone chips. These smaller jobs are a way to change or protect the car without a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Porsche 911 GT2: body, cut-outs and film

The Porsche 911 GT2 vinyl wrap uses two long side doors, and each door is one large piece of film on every generation. The coupe body keeps the panel count lower than a sedan or SUV, but the rear wing and wide rear arches still add surface area. The newest 991 measures 179.1 in (4,549 mm), while the first 996 is 167.1 in (4,245 mm). A wrap installer plans the film around the long doors, the roof, and the large rear haunches.

Porsche 911 GT2 wrap ideas often begin with the parts that need cut-outs or come off before the film goes on. The 997 generation has fog lamps in the front bumper on every trim, so the bumper film needs cut-outs around those lamps. The 997 also has a tall body at 71.9 in (1,825 mm), so the roof is wrapped from a platform. On all GT2 generations, the door handles, mirrors, and badges should be removed for a cleaner install.

How much vinyl to wrap a Porsche 911 GT2 depends on the generation and the film pattern, because the four bodies are not the same size. The third-generation 997 needs about 56 ft (17 m) of 60-inch (1.52 m) cast film, the most of any GT2. The fourth-generation 991 and the second-generation 996 need about 49 ft (15 m) each. The first-generation 996 is the shortest at 167.1 in (4,245 mm) and takes about 46 ft (14 m).

Questions about wrapping a Porsche 911 GT2

How much vinyl does it take to wrap a Porsche 911 GT2?

A full Porsche 911 GT2 wrap takes about 49 ft (15 m) of 60-inch (1.52 m) cast film for the newest 991 body. For a chrome or patterned film, allow about 56 ft (17 m) because the pattern must align across the panels. The first-generation 996 uses about 46 ft (14 m), and the third-generation 997 uses about 56 ft (17 m).

Can I wrap only the hood or the roof of a Porsche 911 GT2?

Yes, you can wrap only the hood or the roof of a Porsche 911 GT2. A partial wrap covers the roof, hood, and mirror caps, and it is a smaller job than a full wrap. You can also choose a chrome delete for the window trim and badges. Paint protection film on the front end is another partial option.

Is a Porsche 911 GT2 hard to wrap?

A Porsche 911 GT2 is not the hardest car to wrap, but the long side doors and the wide rear arches add work. The 997 generation is tall at 71.9 in (1,825 mm), so the roof is wrapped from a platform. Every trim of the 997 has fog lamps in the front bumper, which means cut-outs in the bumper film. The two long side doors each need one large piece of film, so an extra pair of hands helps.

How many generations of the Porsche 911 GT2 does this page cover?

This page covers four generations of the Porsche 911 GT2, from the first 996 in 1995–1998 to the fourth 991 in 2017–2019. The bodies are all two-door coupes, but the lengths and film amounts differ. The first generation takes about 46 ft (14 m) of film, the second and fourth about 49 ft (15 m), and the third about 56 ft (17 m).