Wraps by car

Porsche Carrera GT wrap

The Porsche Carrera GT wrap page covers the 2003–2007 sports car with its one generation in the catalog. A full wrap takes about 43 ft (13 m) of 60-inch (1.52 m) cast vinyl wrap. Chrome or patterned film needs about 54 ft (16.5 m) of the same width.

1generations13 mof film for a full wrap

Porsche Carrera GT, first generation, factory photo
Porsche Carrera GT, first generation. Factory color shown.

Porsche Carrera GT wrap colors and ideas

  • Carrera GT black wrap
  • Carrera GT white wrap
  • Carrera GT gray wrap
  • Carrera GT silver wrap
  • Carrera GT red wrap
  • Carrera GT blue wrap
  • Carrera GT green wrap
  • Carrera GT yellow wrap
  • Carrera GT orange wrap
  • Carrera GT purple wrap
  • Carrera GT pink wrap
  • Carrera GT teal wrap
  • Carrera GT brown wrap
  • Carrera GT gold wrap
  • Carrera GT chrome wrap
  • Carrera GT color shift wrap
  • Carrera GT carbon fiber wrap
  • Carrera GT camo and patterned wrap

How much vinyl to wrap a Porsche Carrera GT

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2003–2007targa (2 doors)181.6 in (4,613 mm)about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m)

Carrera GT wrap cost factors

Carrera GT wrap cost depends on the film type and the labor the targa body requires. Standard cast film needs about 43 ft (13 m), while chrome or patterned film calls for about 54 ft (16.5 m). The open roof and the deep intakes add time for edge work and cut-outs, which affects what an installer quotes.

  • Film for a full wrap: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).
  • Body: targa (2 doors).
  • Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Carrera GT wraps by generation

Swipe sideways. Tap a card for the full description.

Porsche Carrera GT, first generation, factory photo
Factory color shown

2003–2007 Carrera GT targa (first generation)

2003–2007targa (2 doors)181.6 in (4,613 mm)

The Porsche Carrera GT first generation has a targa top that is not wrapped as one surface. The fabric top is left as it is and the film ends where the top begins, so the line has to be straight and clean. If the car has a folding hard top, each panel is wrapped on its own to keep the edges neat.

Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).

Roof, hood, chrome delete and PPF on a Carrera GT

A partial wrap on a Carrera GT can cover the hood, mirror caps or rear deck instead of the whole car. A chrome delete turns the window trim and badges black with vinyl film. Paint protection film is another smaller job, with clear film laid on the front end to guard against stone chips.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Porsche Carrera GT: body, cut-outs and film

A Porsche Carrera GT vinyl wrap must follow the targa body with its two doors and 181.6 in (4,613 mm) length. The open top means the film ends where the roof panel begins, so the installer plans clean edges around that opening. The car's wide rear haunches and low nose add compound curves that call for careful stretching of the film.

Carrera GT wrap ideas begin with the targa top, because the fabric part is not wrapped and the film stops where it starts. A folding hard top, if fitted, is wrapped as its own separate panels so the seams stay controllable. The side intakes and the rear diffuser need precise cut-outs, and the mirrors may come off for a tidier edge.

When you count how much vinyl to wrap a Carrera GT, every car in the catalog belongs to the same 2003–2007 first generation. The body length of 181.6 in (4,613 mm) does not change between production years. With a single generation, the film estimate of about 43 ft (13 m) for standard cast film stays the same for every Carrera GT.

Questions about wrapping a Porsche Carrera GT

How much vinyl does it take to wrap a Porsche Carrera GT?

It takes about 43 ft (13 m) of 60-inch (1.52 m) cast vinyl to wrap a Porsche Carrera GT. If you use chrome or patterned film, the estimate rises to about 54 ft (16.5 m) of the same 60-inch (1.52 m) width.

Is the top of a Carrera GT wrapped?

No, the top of a Carrera GT is not wrapped when it is the standard fabric targa roof. The vinyl film ends where the roof begins because the fabric does not hold the film well. A folding hard top, when present, is wrapped as its own separate panels.

Can I wrap only the hood or the roof of a Carrera GT?

Yes, you can wrap only the hood or the rear deck of a Carrera GT as a partial job. Mirror caps and a chrome delete on the window trim and badges are also common smaller wraps. Paint protection film on the front end is another option that does not cover the whole car.

Is a Carrera GT hard to wrap?

Yes, a Carrera GT is hard to wrap because the targa roof interrupts the main body line and needs a clean film edge where the top begins. The car measures 181.6 in (4,613 mm), so a full wrap uses about 43 ft (13 m) of film. Deep intakes and the low nose add more time for precise cut-outs and stretching.