Wraps by car

Chevrolet Beretta wrap

The Chevrolet Beretta wrap page covers the first generation coupe made from 1987 to 1996. This catalog lists one generation of the car. A full wrap of the newest body takes about 49 ft (15 m) of 60-inch (1.52 m) cast film. Chrome or patterned film for the same body takes about 62 ft (19 m).

1generations15 mof film for a full wrap

Chevrolet Beretta, first generation, factory photo
Chevrolet Beretta, first generation. Factory color shown.

Chevrolet Beretta wrap colors and ideas

  • Beretta black wrap
  • Beretta white wrap
  • Beretta gray wrap
  • Beretta silver wrap
  • Beretta red wrap
  • Beretta blue wrap
  • Beretta green wrap
  • Beretta yellow wrap
  • Beretta orange wrap
  • Beretta purple wrap
  • Beretta pink wrap
  • Beretta teal wrap
  • Beretta brown wrap
  • Beretta gold wrap
  • Beretta chrome wrap
  • Beretta color shift wrap
  • Beretta carbon fiber wrap
  • Beretta camo and patterned wrap

How much vinyl to wrap a Chevrolet Beretta

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1987–1996coupe (2 doors)187.3 in (4,757 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m)

Beretta wrap cost factors

Beretta wrap cost depends on the film finish and the condition of the paint. The base estimate is about 49 ft (15 m) of 60-inch (1.52 m) cast film, while chrome or patterned film needs about 62 ft (19 m). More complex finishes raise the material cost. Paint condition also matters because chips and scratches must be corrected before the film goes on.

  • Film for a full wrap: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Beretta wraps by generation

Swipe sideways. Tap a card for the full description.

Chevrolet Beretta, first generation, factory photo
Factory color shown

1987–1996 Beretta coupe (first generation)

1987–1996coupe (2 doors)187.3 in (4,757 mm)

The first generation Chevrolet Beretta was produced from 1987 to 1996 as a two-door coupe. On a car of these years panels may be original or repainted, and a test spot comes before a full wrap. The paint may have different adhesion levels across the body. A test spot shows whether the film will stick evenly to each panel.

Two long side doors: each door is one large piece of film.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).

Roof, hood, chrome delete and PPF on a Beretta

A Beretta chrome delete covers the window trim and badges with black film. A partial wrap can cover the roof, hood, or mirror caps on their own. Paint protection film (PPF) is also possible on the front end with a clear film. These smaller jobs are good options when you do not want a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Chevrolet Beretta: body, cut-outs and film

A Chevrolet Beretta vinyl wrap has to handle one body style: a two-door coupe that is 187.3 in (4,757 mm) long. The compact size keeps the wrap smaller than on larger coupes, but the doors are long for the car's length. Each side door is one large piece of film, so the installer must work across a broad flat panel. The roof and rear quarter panels round out the main surfaces.

Beretta wrap ideas start with the two long side doors, which are the main surfaces to cover. The door handles, mirrors, and badges come off or get cut around carefully. The front and rear bumpers are wrapped on the car, with cuts made around lights and grilles. The window trim can be covered separately for a chrome delete.

Anyone checking how much vinyl to wrap a Beretta will find only one generation in this catalog. That means the film estimate stays the same across all years from 1987 to 1996. You do not need to compare different body sizes or styles. The only change comes from the finish: chrome or patterned film requires more material because of pattern matching.

Questions about wrapping a Chevrolet Beretta

How much vinyl does it take to wrap a Chevrolet Beretta?

It takes about 49 ft (15 m) of 60-inch (1.52 m) cast film to wrap a Chevrolet Beretta. For chrome or patterned film, the estimate is about 62 ft (19 m). The figures are for the newest body of the first generation coupe.

Can I wrap only the hood or the roof of a Beretta?

Yes, you can wrap only the hood or the roof of a Beretta. A partial wrap can cover the roof, hood, or mirror caps separately. You can also do a chrome delete on the window trim and badges, or apply paint protection film (PPF) on the front end.

Is a Beretta hard to wrap?

A Beretta adds some work because of the two long side doors, each one a large piece of film. The coupe body is 187.3 in (4,757 mm) long, so the doors are long for a compact car. That means careful handling to avoid wrinkles and air bubbles. The rest of the car is straightforward for a professional installer.

How many generations of the Beretta does this page cover?

This page covers one generation of the Beretta. That generation is the first, produced from 1987 to 1996 as a two-door coupe.