Wraps by car

Chevrolet Lumina APV wrap

The Chevrolet Lumina APV wrap page covers the first-generation minivan built from 1989 to 1996. A full vinyl wrap of the newest body takes about 70 ft (21.5 m) of 60-inch (1.52 m) cast film. The page explains how the van's size and sliding doors shape the job, which parts need extra work, and what a partial wrap can include.

1generations21.5 mof film for a full wrap

Chevrolet Lumina APV, first generation, factory photo
Chevrolet Lumina APV, first generation. Factory color shown.

Chevrolet Lumina APV wrap colors and ideas

  • Lumina APV black wrap
  • Lumina APV white wrap
  • Lumina APV gray wrap
  • Lumina APV silver wrap
  • Lumina APV red wrap
  • Lumina APV blue wrap
  • Lumina APV green wrap
  • Lumina APV yellow wrap
  • Lumina APV orange wrap
  • Lumina APV purple wrap
  • Lumina APV pink wrap
  • Lumina APV teal wrap
  • Lumina APV brown wrap
  • Lumina APV gold wrap
  • Lumina APV chrome wrap
  • Lumina APV color shift wrap
  • Lumina APV carbon fiber wrap
  • Lumina APV camo and patterned wrap

How much vinyl to wrap a Chevrolet Lumina APV

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1989–1996van (5 doors)190.7 in (4,844 mm)about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 84 ft (25.5 m)

Lumina APV wrap cost factors

The Lumina APV wrap cost depends on the size of the van and the film you choose. A full wrap needs about 70 ft (21.5 m) of 60-inch (1.52 m) cast film, and chrome or patterned film raises the amount to about 84 ft (25.5 m). The sliding door tracks add labor because the film has to be cut carefully along them. Paint condition before the wrap also affects the preparation work.

  • Film for a full wrap: about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 84 ft (25.5 m).
  • Body: van (5 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.

Lumina APV wraps by generation

Swipe sideways. Tap a card for the full description.

Chevrolet Lumina APV, first generation, factory photo
Factory color shown

1989–1996 Lumina APV van (first generation)

1989–1996van (5 doors)190.7 in (4,844 mm)

The first-generation Chevrolet Lumina APV has sliding side doors that decide where the film is cut. The door tracks stay bare, so the film edge follows the tracks and the doors can still slide. This body style was the only one made from 1989 to 1996, and it needs about 70 ft (21.5 m) of 60-inch (1.52 m) cast film for a full wrap. The large roof and hood also add surface area to cover.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 84 ft (25.5 m).

Roof, hood, chrome delete and PPF on a Lumina APV

A partial wrap on a Lumina APV can cover the roof, hood, or mirror caps with vinyl film. A chrome delete covers the window trim and badges with black film for a different look. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. These smaller jobs use less film than a full wrap and can be done without touching the sliding doors.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Chevrolet Lumina APV: body, cut-outs and film

The Chevrolet Lumina APV vinyl wrap has to cover a large five-door minivan body. The van is 190.7 in (4,844 mm) long, so a full wrap uses about 70 ft (21.5 m) of 60-inch (1.52 m) cast film. The tall roof and long hood add surface area compared with a smaller car. A single body style keeps the pattern predictable, but the size makes a full wrap a two-person job.

Lumina APV wrap ideas start with careful work around the sliding side doors. The door tracks stay bare, and the film is cut along them so the doors can open and close freely. Door handles, mirrors, and badges are removed for a clean install, and the edges are wrapped or cut around. The front and rear bumpers are wrapped on the vehicle because they flex too much off it.

How much vinyl to wrap a Lumina APV depends on the film and the one generation made. Every first-generation van from 1989 to 1996 needs the same amount of cast film, about 70 ft (21.5 m) of 60-inch (1.52 m) material. Chrome or patterned film requires about 84 ft (25.5 m) because the pattern has to be matched. Installers add extra for mistakes and for wrapping the door edges.

Questions about wrapping a Chevrolet Lumina APV

How much vinyl does it take to wrap a Chevrolet Lumina APV?

A Chevrolet Lumina APV needs about 70 ft (21.5 m) of 60-inch (1.52 m) cast film for a full wrap. That figure covers the first-generation van from 1989 to 1996, the only one made. Chrome or patterned film requires about 84 ft (25.5 m) because the pattern has to be matched.

Are the sliding doors of a Lumina APV wrapped?

Yes, the sliding doors of a Lumina APV are wrapped, but the door tracks stay bare. The film is cut along the tracks so the doors can open and close without catching. The edges around the tracks are wrapped or sealed to keep the film from lifting.

Can I wrap only the hood or the roof of a Lumina APV?

Yes, you can wrap only the hood or the roof of a Lumina APV. A partial wrap can cover the roof, hood, or mirror caps, or you can get a chrome delete on the window trim and badges. Paint protection film is another option, applied to the front end as a clear layer.

Is a Lumina APV hard to wrap?

Yes, a Lumina APV is harder to wrap than a smaller car because of its size and sliding doors. The van is 190.7 in (4,844 mm) long, so a full wrap takes about 70 ft (21.5 m) of 60-inch (1.52 m) film and more time to install. The sliding door tracks must stay bare, and the film has to be cut carefully along them, which adds labor.