Wraps by car

Opel Speedster wrap

This page covers the Opel Speedster wrap, a vinyl wrap job on the two-seat targa sports car. The Opel Speedster has one generation in this catalog, produced from 2000 to 2005. A full wrap of the newest body takes about 34 ft (10.5 m) of 60-inch (1.52 m) cast film.

1generations10.5 mof film for a full wrap

Opel Speedster, first generation, factory photo
Opel Speedster, first generation. Factory color shown.

Opel Speedster wrap colors and ideas

  • Speedster black wrap
  • Speedster white wrap
  • Speedster gray wrap
  • Speedster silver wrap
  • Speedster red wrap
  • Speedster blue wrap
  • Speedster green wrap
  • Speedster yellow wrap
  • Speedster orange wrap
  • Speedster purple wrap
  • Speedster pink wrap
  • Speedster teal wrap
  • Speedster brown wrap
  • Speedster gold wrap
  • Speedster chrome wrap
  • Speedster color shift wrap
  • Speedster carbon fiber wrap
  • Speedster camo and patterned wrap

How much vinyl to wrap an Opel Speedster

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2000–2005targa (2 doors)149.2 in (3,790 mm)about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m)

Speedster wrap cost factors

The Speedster wrap cost depends on the size of the body, the film chosen, and the labor for the curves and cut-outs. The car is 149.2 in (3,790 mm) long and needs about 34 ft (10.5 m) of 60-inch (1.52 m) cast film for a full color change. Chrome or patterned film uses about 46 ft (14 m) because the pattern must be aligned. A partial wrap costs less film and less time than a full wrap.

  • Film for a full wrap: about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).
  • Body: targa (2 doors).
  • Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Speedster wraps by generation

Swipe sideways. Tap a card for the full description.

Opel Speedster, first generation, factory photo
Factory color shown

2000–2005 Speedster targa (first generation)

2000–2005targa (2 doors)149.2 in (3,790 mm)

The first generation Speedster has an open targa top that is not wrapped in vinyl. If the car has a fabric top, the film ends where the top begins, leaving the fabric uncovered. With the folding hard top, those roof panels are wrapped separately so the film does not bridge the gap.

Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 34 ft (10.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).

Roof, hood, chrome delete and PPF on a Speedster

A partial wrap on an Opel Speedster can cover the hood, mirror caps, and rear deck only. Chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Opel Speedster: body, cut-outs and film

The Opel Speedster vinyl wrap is shaped by its single targa body style with two doors. The body is 149.2 in (3,790 mm) long, so a full wrap needs about 34 ft (10.5 m) of 60-inch (1.52 m) film. Because the car is small and has few flat panels, installers cut film in shorter pieces and use more relief cuts on the curved rear deck.

For Speedster wrap ideas, the targa body means the fabric top is not wrapped and the film ends where the top begins. A folding hard top, when fitted, is wrapped as its own panels. The mirrors, door handles and badges are removed so the film can be tucked behind them, and the front bumper vents need cut-outs around the openings.

To see how much vinyl to wrap a Speedster, compare the single generation offered from 2000 to 2005. All years share the same targa body and the same 149.2 in (3,790 mm) length, so the film estimate stays at about 34 ft (10.5 m). A car with a folding hard top adds the film for those roof panels, while the fabric top car uses less.

Questions about wrapping an Opel Speedster

How much vinyl does it take to wrap an Opel Speedster?

It takes about 34 ft (10.5 m) of 60-inch (1.52 m) cast film to wrap an Opel Speedster. This figure is for the targa body of the 2000–2005 generation. Chrome or patterned film needs about 46 ft (14 m) because the pattern must be matched.

Is the top of a Speedster wrapped?

No, the top of a Speedster is not wrapped. The fabric top is left uncovered, and the vinyl film ends where the top begins. Only a folding hard top is wrapped, as its own panels.

Can I wrap only the hood or the roof of a Speedster?

Yes, you can wrap only the hood, mirror caps, or rear deck of a Speedster. A partial wrap can cover those smaller areas. Chrome delete is another option for the window trim and badges.

Is a Speedster hard to wrap?

Yes, a Speedster is harder to wrap than a sedan because of its small size and curved rear deck. The targa body means the film must end cleanly at the open top, and installers must work around the cut-outs for the front bumper vents. The rear deck has tight curves that need careful stretching of the film.