Wraps by car

Porsche 912 wrap

The Porsche 912 wrap page covers both generations of this classic sports car. A full vinyl wrap of the second generation coupe takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. The first generation coupe and targa use slightly less, at about 43 ft (13 m) to 44 ft (13.5 m).

2generations14 mof film for a full wrap

Porsche 912, second generation, factory photo
Porsche 912, second generation. Factory color shown.

Porsche 912 wrap colors and ideas

  • Porsche 912 black wrap
  • Porsche 912 white wrap
  • Porsche 912 gray wrap
  • Porsche 912 silver wrap
  • Porsche 912 red wrap
  • Porsche 912 blue wrap
  • Porsche 912 green wrap
  • Porsche 912 yellow wrap
  • Porsche 912 orange wrap
  • Porsche 912 purple wrap
  • Porsche 912 pink wrap
  • Porsche 912 teal wrap
  • Porsche 912 brown wrap
  • Porsche 912 gold wrap
  • Porsche 912 chrome wrap
  • Porsche 912 color shift wrap
  • Porsche 912 carbon fiber wrap
  • Porsche 912 camo and patterned wrap

How much vinyl to wrap a Porsche 912

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1975–1976coupe (2 doors)168.9 in (4,291 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m)
1965–1969coupe, targa (2 doors)163.9 in (4,163 mm)about 43 ft (13 m) for the targa to 44 ft (13.5 m) for the coupe, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 51 ft (15.5 m)

Porsche 912 wrap cost factors

The Porsche 912 wrap cost depends mainly on film area, body style, and paint preparation. A first generation targa uses about 43 ft (13 m) of film, a coupe about 44 ft (13.5 m), and a second generation coupe about 46 ft (14 m). Chrome or patterned film raises the amount to about 57 ft (17.5 m) on the later car. Panel condition and any needed repair work also affect the final estimate.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Porsche 912 wraps by generation

Swipe sideways. Tap a card for the full description.

Porsche 912, second generation, factory photo
Factory color shown

1975–1976 Porsche 912 coupe (second generation)

1975–1976coupe (2 doors)168.9 in (4,291 mm)

The second generation Porsche 912 was built in 1975 and 1976 as a coupe, with a length of 168.9 in (4,291 mm). Paint may be original or repainted, so a test spot is necessary before a full wrap. This check shows whether the film will bond cleanly to the surface and helps avoid lifting later.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).

Porsche 912, first generation, factory photo
Factory color shown

1965–1969 Porsche 912 coupe, targa (first generation)

1965–1969coupe, targa (2 doors)163.9 in (4,163 mm)

The first generation Porsche 912 from 1965 to 1969 came as a coupe or targa, measuring 163.9 in (4,163 mm). On an open top, the fabric section is not wrapped and the film ends where the material begins. A folding hard top is wrapped as separate panels of its own, matching the body lines.

Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Two long side doors: each door is one large piece of film.

Film: about 43 ft (13 m) for the targa to 44 ft (13.5 m) for the coupe, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Porsche 912

A partial wrap on a Porsche 912 can cover the roof, hood, or mirror caps for a focused change. Porsche 912 chrome delete uses black film on window trim and badges to replace bright metal. Paint protection film (PPF) as a clear film on the front end shields the nose from stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Porsche 912: body, cut-outs and film

The Porsche 912 vinyl wrap must handle two long side doors, each installed as one large piece of film. The first generation measures 163.9 in (4,163 mm) and the second is 168.9 in (4,291 mm) long. Coupe and targa bodies have similar panel counts, while the targa requires careful planning around the roof opening. These compact dimensions keep the wrap area modest for a sports car.

Porsche 912 wrap ideas often focus on the doors, which need the largest film pieces. Each door is wrapped as one sheet to avoid visible seams along the long panel. The targa body adds a decision point: the fabric top is not wrapped and the film ends where it begins. A folding hard top is wrapped as its own separate panels.

How much vinyl to wrap a Porsche 912 depends on the generation and body style. For the first generation, a targa uses about 43 ft (13 m) and a coupe about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. The second generation coupe requires about 46 ft (14 m). Adding chrome or patterned film increases the total to up to about 57 ft (17.5 m) on the later car.

Questions about wrapping a Porsche 912

How much vinyl does it take to wrap a Porsche 912?

A full wrap of a Porsche 912 takes about 46 ft (14 m) of 60-inch (1.52 m) cast film for the newest body. The second generation coupe is the largest version, while first generation cars use slightly less material.

Can I wrap only the hood or the roof of a Porsche 912?

Yes, you can wrap only the hood or the roof of a Porsche 912 as a partial job. Mirror caps are another common single-panel option, along with chrome delete on window trim and badges.

Is a Porsche 912 hard to wrap?

A Porsche 912 is moderately hard to wrap because of its two long side doors, each requiring one large piece of film. The targa top adds complexity since the fabric is not wrapped and the film must end cleanly at the opening.

How many generations of the Porsche 912 does this page cover?

This page covers two generations of the Porsche 912. The first generation ran from 1965 to 1969 and the second from 1975 to 1976, with different body styles and film amounts.