Wraps by car

Porsche 924 wrap

The Porsche 924 wrap page covers the first generation, produced from 1975 to 1988. A full vinyl wrap of the coupe body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. Chrome or patterned film requires about 51 ft (15.5 m) of the same width.

1generations14 mof film for a full wrap

Porsche 924, first generation, factory photo
Porsche 924, first generation. Factory color shown.

Porsche 924 wrap colors and ideas

  • Porsche 924 black wrap
  • Porsche 924 white wrap
  • Porsche 924 gray wrap
  • Porsche 924 silver wrap
  • Porsche 924 red wrap
  • Porsche 924 blue wrap
  • Porsche 924 green wrap
  • Porsche 924 yellow wrap
  • Porsche 924 orange wrap
  • Porsche 924 purple wrap
  • Porsche 924 pink wrap
  • Porsche 924 teal wrap
  • Porsche 924 brown wrap
  • Porsche 924 gold wrap
  • Porsche 924 chrome wrap
  • Porsche 924 color shift wrap
  • Porsche 924 carbon fiber wrap
  • Porsche 924 camo and patterned wrap

How much vinyl to wrap a Porsche 924

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1975–1988coupe (2 doors)165.8 in (4,211 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Porsche 924 wrap cost factors

The Porsche 924 wrap cost depends on the amount of film, which is about 46 ft (14 m) of 60-inch (1.52 m) cast vinyl, or 51 ft (15.5 m) for chrome or patterned film. Surface condition matters because a car of these years may have original or repainted panels. The number of cut-outs and removed parts, such as door handles and badges, also adds labor time.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Porsche 924 wraps by generation

Swipe sideways. Tap a card for the full description.

Porsche 924, first generation, factory photo
Factory color shown

1975–1988 Porsche 924 coupe (first generation)

1975–1988coupe (2 doors)165.8 in (4,211 mm)

The first generation Porsche 924 was built from 1975 to 1988 as a two-door coupe. Paint age varies on a car of these years: panels may be original or repainted, so a test spot comes before a full wrap. The long side doors each take one large piece of film, which keeps the sides manageable.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Porsche 924

A partial wrap on a Porsche 924 can cover the roof, hood, or mirror caps. A chrome delete turns the window trim and badges black with film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Porsche 924: body, cut-outs and film

The Porsche 924 coupe has a body length of 165.8 in (4,211 mm), which keeps the footprint of a full wrap modest. Two long side doors each take one large piece of film, so the sides are straightforward for an installer. A Porsche 924 vinyl wrap follows the clean profile of a 1970s sports car without deep recesses.

The wrap ideas for a Porsche 924 start with the two long side doors that are each done as one large piece of film. Door handles, mirrors, and badges need cut-outs or removal before the vinyl goes on. The nose panel and rear hatch are large flat areas that suit a single continuous sheet.

If you count film for a Porsche 924, note that only one generation exists in the catalog, from 1975 to 1988. The body style stayed a two-door coupe for the whole production run, so the estimate does not change. How much vinyl to wrap a Porsche 924 is therefore a fixed quantity for every year of this car.

Questions about wrapping a Porsche 924

How much vinyl does it take to wrap a Porsche 924?

It takes about 46 ft (14 m) of 60-inch (1.52 m) cast film to wrap a Porsche 924. For chrome or patterned film, the figure is about 51 ft (15.5 m) of the same width.

Can I wrap only the hood or the roof of a Porsche 924?

Yes, you can wrap only the hood or the roof of a Porsche 924. A partial wrap on this car typically includes the roof, hood, or mirror caps.

Is a Porsche 924 hard to wrap?

A Porsche 924 is not especially hard to wrap, but the two long side doors each need one large piece of film. The body length of 165.8 in (4,211 mm) is compact for a car, so handling the film is manageable.

How many generations of the Porsche 924 does this page cover?

This page covers one generation of the Porsche 924, produced from 1975 to 1988.