Wraps by car

Ford Bronco-II wrap

This page covers the Ford Bronco-II wrap for the single generation produced from 1984 to 1990. The Bronco-II is a three-door SUV with a body length of 161.9 in (4,112 mm). A full vinyl wrap of this body takes about 56 ft (17 m) of 60-inch (1.52 m) cast film, or about 69 ft (21 m) for chrome or patterned film.

1generations17 mof film for a full wrap

Ford Bronco-II, first generation, factory photo
Ford Bronco-II, first generation. Factory color shown.

Ford Bronco-II wrap colors and ideas

  • Bronco-II black wrap
  • Bronco-II white wrap
  • Bronco-II gray wrap
  • Bronco-II silver wrap
  • Bronco-II red wrap
  • Bronco-II blue wrap
  • Bronco-II green wrap
  • Bronco-II yellow wrap
  • Bronco-II orange wrap
  • Bronco-II purple wrap
  • Bronco-II pink wrap
  • Bronco-II teal wrap
  • Bronco-II brown wrap
  • Bronco-II gold wrap
  • Bronco-II chrome wrap
  • Bronco-II color shift wrap
  • Bronco-II carbon fiber wrap
  • Bronco-II camo and patterned wrap

How much vinyl to wrap a Ford Bronco-II

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1984–1990SUV (3 doors)161.9 in (4,112 mm)about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Bronco-II wrap cost factors

Bronco-II wrap cost depends on the film type and the amount of disassembly. This SUV is 161.9 in (4,112 mm) long and 69.9 in (1,775 mm) tall, so the roof adds time on a platform. The two long doors are large but straightforward, and the tailgate glass means no cut-out work there. A color change wrap uses about 56 ft (17 m) of cast film, while chrome or patterned film needs about 69 ft (21 m).

  • Film for a full wrap: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: SUV (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.
  • A tall body (69.9 in (1,775 mm)): the roof is wrapped from a platform.

Bronco-II wraps by generation

Swipe sideways. Tap a card for the full description.

Ford Bronco-II, first generation, factory photo
Factory color shown

1984–1990 Bronco-II SUV (first generation)

1984–1990SUV (3 doors)161.9 in (4,112 mm)

The first generation Bronco-II, built from 1984 to 1990, has a tall body of 69.9 in (1,775 mm). The roof is wrapped from a platform, which adds time to the job. The sides are easy because each long door is one big piece of film. The tailgate film ends at the edge of the glass, so no trimming is needed around the window.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

A tall body (69.9 in (1,775 mm)): the roof is wrapped from a platform.

Film: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Bronco-II

A partial wrap on the Bronco-II can cover the roof, hood, or mirror caps alone. Bronco-II chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is clear film applied to the front end to guard against stone chips. These jobs use less vinyl than a full wrap and can be done in stages.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Ford Bronco-II: body, cut-outs and film

A Ford Bronco-II vinyl wrap is a compact job for a sport utility vehicle. The three-door layout means only two long side doors to cover, and each door is one large piece of film. With a length of 161.9 in (4,112 mm), the body panels are short, so film pieces are easy to handle. The tall body, at 69.9 in (1,775 mm), requires a platform for the roof but keeps the sides at a comfortable working height.

Bronco-II wrap ideas start with the tailgate: the film ends at the edge of the rear glass, so no cut-out is needed there. The two long side doors each take one large piece, and the door handles are removed for a clean edge. The roof is wrapped from a platform because the body is 69.9 in (1,775 mm) tall. Window trim and badges are removed for chrome delete or left in place under the film as you prefer.

When you figure how much vinyl to wrap a Bronco-II, note there is only one generation in the catalog. The 1984–1990 body uses about 56 ft (17 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds waste from matching, so the estimate is about 69 ft (21 m). The tall roof and two large doors are the main film consumers on this body.

Questions about wrapping a Ford Bronco-II

How much vinyl does it take to wrap a Ford Bronco-II?

It takes about 56 ft (17 m) of 60-inch (1.52 m) cast film to wrap a Ford Bronco-II. That figure is based on the 1984–1990 body with its two long doors and tall roof. Chrome or patterned film raises the estimate to about 69 ft (21 m) because of pattern matching waste.

Can I wrap only the hood or the roof of a Bronco-II?

Yes, you can wrap only the hood or the roof of a Bronco-II. A partial wrap covers the roof, hood, or mirror caps as separate jobs. The hood is a single flat panel, and the roof is tall but straightforward with a platform.

Is a Bronco-II hard to wrap?

A Bronco-II is not hard to wrap but the tall body adds work. The roof is 69.9 in (1,775 mm) high, so a platform is needed to reach it. Each of the two long side doors is one large piece, and the tailgate film ends at the glass, making the job easier.

How many generations of the Bronco-II does this page cover?

This page covers one generation of the Bronco-II, produced from 1984 to 1990.