Wraps by car

Ford Consul wrap

The Ford Consul wrap page covers the single generation built from 1972 to 1976. A full vinyl wrap of the newest body takes about 49 ft (15 m) of film for the coupe and 56 ft (17 m) for the wagon. All figures use 60-inch (1.52 m) cast film.

1generations15 mof film for a full wrap

Ford Consul, first generation, factory photo
Ford Consul, first generation. Factory color shown.

Ford Consul wrap colors and ideas

  • Consul black wrap
  • Consul white wrap
  • Consul gray wrap
  • Consul silver wrap
  • Consul red wrap
  • Consul blue wrap
  • Consul green wrap
  • Consul yellow wrap
  • Consul orange wrap
  • Consul purple wrap
  • Consul pink wrap
  • Consul teal wrap
  • Consul brown wrap
  • Consul gold wrap
  • Consul chrome wrap
  • Consul color shift wrap
  • Consul carbon fiber wrap
  • Consul camo and patterned wrap

How much vinyl to wrap a Ford Consul

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1972–1976coupe, sedan, wagon (2 or 4 or 5 doors)179.8 in (4,568 mm) to 180.5 in (4,585 mm)about 49 ft (15 m) for the coupe to 56 ft (17 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 70 ft (21.5 m)

Consul wrap cost factors

Consul wrap cost depends on the body style, the film type, and the amount of disassembly. The coupe takes about 49 ft (15 m) and the wagon about 56 ft (17 m), so the wagon has more surface to cover. Chrome or patterned film may need up to about 70 ft (21.5 m) for pattern matching. The wrap shop's labor for trim removal and the tailgate glass cut-out also affects the total.

  • Film for a full wrap: about 49 ft (15 m) for the coupe to 56 ft (17 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 70 ft (21.5 m).
  • Body: coupe, sedan, wagon (2 or 4 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Consul wraps by generation

Swipe sideways. Tap a card for the full description.

Ford Consul, first generation, factory photo
Factory color shown

1972–1976 Consul coupe, sedan, wagon (first generation)

1972–1976coupe, sedan, wagon (2 or 4 or 5 doors)179.8 in (4,568 mm) to 180.5 in (4,585 mm)

The first generation Ford Consul was produced from 1972 to 1976 as a coupe, sedan or wagon. The style decides the panel plan and the film amount for a wrap. A coupe takes about 49 ft (15 m) of 60-inch (1.52 m) cast film, while a wagon takes about 56 ft (17 m). The sedan falls between the two.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 49 ft (15 m) for the coupe to 56 ft (17 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 70 ft (21.5 m).

Roof, hood, chrome delete and PPF on a Consul

A partial wrap on a Ford Consul can cover the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film, and it is a smaller job than a full color change wrap. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. These jobs use less film than the full 49 to 56 ft (15 to 17 m) needed for the whole body.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Ford Consul: body, cut-outs and film

A Ford Consul vinyl wrap follows the body style, since the coupe, sedan and wagon each have a different panel plan. The car is 179.8 in (4,568 mm) to 180.5 in (4,585 mm) long, which is a normal full-size job for a shop. The wagon adds a tall tailgate and roof rails, so it uses the most film. The coupe has longer doors that need careful handling around the glass.

Consul wrap ideas should start with the tailgate on the wagon, because the rear glass is set into it. The film ends at the edge of the glass, so the installer trims a clean border around the window. Door handles, mirrors and badges come off for a neat edge. The roof gutters are a straight line that helps with alignment.

To know how much vinyl to wrap a Consul, count the body style first. The coupe takes about 49 ft (15 m), the sedan sits in the middle, and the wagon needs about 56 ft (17 m). A chrome or patterned film calls for up to about 70 ft (21.5 m) to match the pattern. The first generation from 1972 to 1976 offers these three styles.

Questions about wrapping a Ford Consul

How much vinyl does it take to wrap a Ford Consul?

A Ford Consul takes about 49 ft (15 m) of 60-inch (1.52 m) cast film for the coupe and about 56 ft (17 m) for the wagon. These figures are for the first generation body from 1972 to 1976. A chrome or patterned film may need up to about 70 ft (21.5 m).

Which Consul body takes more film?

The wagon takes more film than the coupe or sedan. The coupe uses about 49 ft (15 m) of 60-inch (1.52 m) cast film, while the wagon uses about 56 ft (17 m). The tall tailgate and roof area add surface to cover.

Can I wrap only the hood or the roof of a Consul?

Yes, you can wrap only the hood or the roof of a Consul. A partial wrap can cover the roof, hood, or mirror caps as a separate job. A chrome delete on the window trim and badges is also an option. These smaller jobs use less film than a full wrap.

Is a Consul hard to wrap?

A Consul is not a simple wrap because the wagon tailgate has the rear glass set into it. The film ends at the edge of the glass, so the installer must cut a clean border around the window. The car is about 180 in (4,572 mm) long, which is a standard full-size job. Door handles and badges also come off for a good result.