Wraps by car

Ford Flex wrap

The Ford Flex wrap page covers the 2008–2019 SUV, one generation in the catalog, and a full vinyl wrap of the newest body takes about 67 ft (20.5 m) of 60-inch (1.52 m) cast film.

1generations20.5 mof film for a full wrap

Ford Flex, first generation, factory photo
Ford Flex, first generation. Factory color shown.

Ford Flex wrap colors and ideas

  • Flex black wrap
  • Flex white wrap
  • Flex gray wrap
  • Flex silver wrap
  • Flex red wrap
  • Flex blue wrap
  • Flex green wrap
  • Flex yellow wrap
  • Flex orange wrap
  • Flex purple wrap
  • Flex pink wrap
  • Flex teal wrap
  • Flex brown wrap
  • Flex gold wrap
  • Flex chrome wrap
  • Flex color shift wrap
  • Flex carbon fiber wrap
  • Flex camo and patterned wrap

How much vinyl to wrap a Ford Flex

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2008–2019SUV (5 doors)201.8 in (5,126 mm)about 67 ft (20.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 79 ft (24 m)

Flex wrap cost factors

A Ford Flex wrap cost depends on the film type and the amount of labor for this SUV. The 201.8 in (5,126 mm) long body needs about 67 ft (20.5 m) of vinyl, and patterned or chrome film can require about 79 ft (24 m). The tailgate glass and the restyled bumpers after 2012 add trimming time. Removing door handles and mirrors for a clean install also affects the total.

  • Film for a full wrap: about 67 ft (20.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 79 ft (24 m).
  • Body: SUV (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Restyled in 2012: bumpers and lights differ between the versions, and so do the film cuts.

Flex wraps by generation

Swipe sideways. Tap a card for the full description.

Ford Flex, first generation, factory photo
Factory color shown

2008–2019 Flex SUV (first generation)

2008–2019SUV (5 doors)201.8 in (5,126 mm)

The first-generation Ford Flex was built from 2008 to 2019 and was restyled in 2012. The 2012 update changed the bumpers and lights, so film cut for the earlier version will not fit the later one. The body length stayed at 201.8 in (5,126 mm) through the whole run. If you wrap both versions, count two sets of templates for the front and rear ends.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 67 ft (20.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 79 ft (24 m).

Roof, hood, chrome delete and PPF on a Flex

A partial wrap on a Ford Flex usually covers the roof, hood, or mirror caps, and a chrome delete covers the window trim and badges. The large roof panel is a natural choice for a two-tone look. Clear paint protection film (PPF) on the front end is another option for the long hood and bumper. Each of these jobs uses less film than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Ford Flex: body, cut-outs and film

A Ford Flex vinyl wrap has to cover a long, boxy five-door body measuring 201.8 in (5,126 mm) end to end. The large flat sides and tall roof use film quickly, so most of the 67 ft (20.5 m) goes into those panels. The liftgate and four doors add more area than a small crossover. A full wrap also includes the bumpers and rocker panels, so the total stays within the estimate for the first-generation body.

Flex wrap ideas often start with the tailgate, where the rear glass sits inside the panel and the film must end at the edge of the glass. The tailgate is one large piece, but the glass area is not wrapped, so the installer trims around it. The door handles and mirror caps come off for clean edges. The roof rails, if present, also need to be worked around.

To figure how much vinyl to wrap a Flex, you use the same first-generation body from 2008 to 2019, but the 2012 restyling changed the bumpers and lights. A film kit cut for a 2008–2011 Flex will not fit a 2012–2019 Flex at the front or rear. The body sides and roof are unchanged, so the length and overall area stay the same. The film estimate of about 67 ft (20.5 m) still covers either version, but separate templates are needed for the restyled ends.

Questions about wrapping a Ford Flex

How much vinyl does it take to wrap a Ford Flex?

It takes about 67 ft (20.5 m) of 60-inch (1.52 m) cast film to wrap a Ford Flex. For chrome or patterned film, plan about 79 ft (24 m).

Which years of the Flex take the same film cuts?

The 2008–2011 and 2012–2019 Ford Flex models need different film cuts for the bumpers and lights because of the 2012 restyling.

Can I wrap only the hood or the roof of a Flex?

Yes, you can wrap only the hood or the roof of a Flex, and a partial wrap often includes the roof, hood, or mirror caps.

Is a Flex hard to wrap?

A Flex is not hard to wrap, but the tailgate glass set into the panel and the large body size add work for the installer.