Wraps by car

Ford GPW wrap

This page covers the Ford GPW wrap, a vinyl wrap for the military open-top SUV built from 1942 to 1945. The catalog holds one generation of this car, the first and only body style. A full wrap of that body takes about 39 ft (12 m) of 60-inch (1.52 m) cast film. Chrome or patterned film raises the estimate to about 44 ft (13.5 m).

1generations12 mof film for a full wrap

Ford GPW, first generation, factory photo
Ford GPW, first generation. Factory color shown.

Ford GPW wrap colors and ideas

  • Ford GPW black wrap
  • Ford GPW white wrap
  • Ford GPW gray wrap
  • Ford GPW silver wrap
  • Ford GPW red wrap
  • Ford GPW blue wrap
  • Ford GPW green wrap
  • Ford GPW yellow wrap
  • Ford GPW orange wrap
  • Ford GPW purple wrap
  • Ford GPW pink wrap
  • Ford GPW teal wrap
  • Ford GPW brown wrap
  • Ford GPW gold wrap
  • Ford GPW chrome wrap
  • Ford GPW color shift wrap
  • Ford GPW carbon fiber wrap
  • Ford GPW camo and patterned wrap

How much vinyl to wrap a Ford GPW

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1942–1945open-top SUV131.9 in (3,350 mm)about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m)

Ford GPW wrap cost factors

Ford GPW wrap cost depends on the area covered and the film chosen, not on a simple flat rate. A full wrap needs about 39 ft (12 m) of cast film, or about 44 ft (13.5 m) for chrome or patterned film. The tall 69.7 in (1,770 mm) body adds labor because the roof is wrapped from a platform. The tailgate glass and fabric top edges also add detail work.

  • Film for a full wrap: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).
  • Body: open-top SUV.
  • Open-top SUV body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • A tall body (69.7 in (1,770 mm)): the roof is wrapped from a platform.

Ford GPW wraps by generation

Swipe sideways. Tap a card for the full description.

Ford GPW, first generation, factory photo
Factory color shown

1942–1945 Ford GPW open-top SUV (first generation)

1942–1945open-top SUV131.9 in (3,350 mm)

In the first generation Ford GPW, the open top means the film has a fixed stopping point. The fabric top is left uncovered, so the installer runs the film up to the edge where the top begins. If your GPW has a folding hard top, that top is wrapped separately as its own panels. This keeps the wrap line clean and avoids stress at the hinge points.

Open-top SUV body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

A tall body (69.7 in (1,770 mm)): the roof is wrapped from a platform.

Film: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).

Roof, hood, chrome delete and PPF on a Ford GPW

For a Ford GPW partial wrap, you can wrap the hood, mirror caps, or the tailgate separately. A chrome delete covers the window trim and badges with black film, and it can be done alongside a partial wrap. Paint protection film (PPF) is clear film applied to the front end. These smaller jobs use less film than a full wrap and still change the look or protect the paint.

  • Partial wrap: hood, mirror caps, tailgate.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Ford GPW: body, cut-outs and film

A Ford GPW vinyl wrap has to follow an open-top SUV body that measures 131.9 in (3,350 mm) long. The tall body, 69.7 in (1,770 mm) high, means the roof is wrapped from a platform for safe access. The fabric top is not wrapped, and the film ends where that top begins. A folding hard top is wrapped as panels of its own.

Ford GPW wrap ideas start with leaving the fabric top uncovered and ending the film at its edge. The tailgate has the rear glass in it, so the film must end at the edge of the glass. The tall body makes the roof a two-person job from a platform. Cut-outs are kept to the glass areas and any badges you choose to keep.

To know how much vinyl to wrap a Ford GPW, start with the only generation in the catalog, the first one from 1942–1945. Its body is a single open-top SUV style, so the film estimate stays the same across the years. You need about 39 ft (12 m) of 60-inch (1.52 m) cast film for a full wrap. If you pick a chrome or patterned film, allow about 44 ft (13.5 m).

Questions about wrapping a Ford GPW

How much vinyl does it take to wrap a Ford GPW?

A Ford GPW full wrap takes about 39 ft (12 m) of 60-inch (1.52 m) cast film. If you choose a chrome or patterned film, the estimate goes up to about 44 ft (13.5 m). The figure is based on the only body style in the catalog, the open-top SUV from 1942–1945.

Is the top of a Ford GPW wrapped?

The top of a Ford GPW is not wrapped when it is the standard fabric top. The film ends at the edge where the fabric begins. If your GPW has a folding hard top, that top is wrapped as panels of its own.

Can I wrap only the hood or the roof of a Ford GPW?

Yes, you can wrap only the hood or the roof of a Ford GPW as a partial wrap. A partial wrap can cover the hood, mirror caps, or tailgate on their own. You can also add a chrome delete or paint protection film to those areas.

Is a Ford GPW hard to wrap?

A Ford GPW is not the easiest vehicle to wrap because of its tall body and open-top design. The roof area, at 69.7 in (1,770 mm) high, must be wrapped from a platform. The fabric top edge and the tailgate glass need careful cutting so the film ends cleanly.