Wraps by car

Maserati 228 wrap

The Maserati 228 wrap page covers this single-generation sports car, produced from 1986 to 1992 as a two-door coupe. A full vinyl wrap of the first generation body requires about 49 ft (15 m) of 60-inch (1.52 m) cast film. If you choose a chrome or patterned film, plan for about 56 ft (17 m).

1generations15 mof film for a full wrap

Maserati 228, first generation, factory photo
Maserati 228, first generation. Factory color shown.

Maserati 228 wrap colors and ideas

  • Maserati 228 black wrap
  • Maserati 228 white wrap
  • Maserati 228 gray wrap
  • Maserati 228 silver wrap
  • Maserati 228 red wrap
  • Maserati 228 blue wrap
  • Maserati 228 green wrap
  • Maserati 228 yellow wrap
  • Maserati 228 orange wrap
  • Maserati 228 purple wrap
  • Maserati 228 pink wrap
  • Maserati 228 teal wrap
  • Maserati 228 brown wrap
  • Maserati 228 gold wrap
  • Maserati 228 chrome wrap
  • Maserati 228 color shift wrap
  • Maserati 228 carbon fiber wrap
  • Maserati 228 camo and patterned wrap

How much vinyl to wrap a Maserati 228

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1986–1992coupe (2 doors)175.6 in (4,460 mm)about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)

Maserati 228 wrap cost factors

Maserati 228 wrap cost depends mainly on the film type and the labor needed for a 175.6 in (4,460 mm) coupe. A full color change with cast film uses about 49 ft (15 m), while chrome or patterned film uses about 56 ft (17 m). The condition of the body and how much trim is removed also change the final cost.

  • Film for a full wrap: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Maserati 228 wraps by generation

Swipe sideways. Tap a card for the full description.

Maserati 228, first generation, factory photo
Factory color shown

1986–1992 Maserati 228 coupe (first generation)

1986–1992coupe (2 doors)175.6 in (4,460 mm)

The first generation Maserati 228 is the only body this page covers, a coupe built from 1986 to 1992. Before wrapping, check the paint age because panels may be original or repainted, and a test spot comes before a full wrap. Old paint can lift when the film is repositioned, so an installer must work slowly on this car.

Two long side doors: each door is one large piece of film.

Film: about 49 ft (15 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Roof, hood, chrome delete and PPF on a Maserati 228

A partial wrap on a Maserati 228 is a practical choice for the roof, hood, or mirror caps. Chrome delete covers the window trim and badges, and paint protection film (PPF) is a clear film for the front end. These smaller jobs use much less film than a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Maserati 228: body, cut-outs and film

A Maserati 228 vinyl wrap follows the coupe's simple two-door shape but uses a lot of film because the car is 175.6 in (4,460 mm) long. The long doors and large rear quarter panels are the main flat areas, while the nose and tail need careful stretching around compound curves. Allow extra material for the bumpers and the deep rocker panels.

Maserati 228 wrap ideas often start with the two long side doors, and each door takes one large piece of film to avoid seams. The door handles, mirrors and side trim must be removed for a clean install. The front and rear bumpers come off the car so the film can wrap fully around their edges.

To work out how much vinyl to wrap a Maserati 228, start with the model's single generation built from 1986 to 1992. There are no shorter or longer body styles, so the film estimate stays the same for every 228. A careful installer may use slightly more film if the paint is rough or if extra panels need redoing.

Questions about wrapping a Maserati 228

How much vinyl does it take to wrap a Maserati 228?

A full wrap of a Maserati 228 takes about 49 ft (15 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, plan for about 56 ft (17 m). These figures cover the whole coupe body.

Can I wrap only the hood or the roof of a Maserati 228?

Yes, a partial wrap lets you cover only the hood or the roof of a Maserati 228. The same applies to the mirror caps, and chrome delete can be done on the window trim and badges. Paint protection film (PPF) is another partial option for just the front end.

Is a Maserati 228 hard to wrap?

A Maserati 228 is not especially hard to wrap because it has a simple coupe shape, but the two long side doors each need one large piece of film. The car's 175.6 in (4,460 mm) length adds work when handling big sheets. Careful removal of trim and bumpers also adds time.

How many generations of the Maserati 228 does this page cover?

The Maserati 228 has one generation, built from 1986 to 1992 as a two-door coupe. This page covers that single generation.