Wraps by car

Maserati Chubasco wrap

The Maserati Chubasco wrap page covers the full vinyl wrap of this one-generation sports car. The Chubasco was built in 1990 and offered one body style, a coupe with two doors. A complete wrap of its body uses about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, plan for about 56 ft (17 m).

1generations13.5 mof film for a full wrap

Maserati Chubasco, first generation, factory photo
Maserati Chubasco, first generation. Factory color shown.

Maserati Chubasco wrap colors and ideas

  • Chubasco black wrap
  • Chubasco white wrap
  • Chubasco gray wrap
  • Chubasco silver wrap
  • Chubasco red wrap
  • Chubasco blue wrap
  • Chubasco green wrap
  • Chubasco yellow wrap
  • Chubasco orange wrap
  • Chubasco purple wrap
  • Chubasco pink wrap
  • Chubasco teal wrap
  • Chubasco brown wrap
  • Chubasco gold wrap
  • Chubasco chrome wrap
  • Chubasco color shift wrap
  • Chubasco carbon fiber wrap
  • Chubasco camo and patterned wrap

How much vinyl to wrap a Maserati Chubasco

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1990–1990coupe (2 doors)171.9 in (4,365 mm)about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)

Chubasco wrap cost factors

Chubasco wrap cost depends first on the size of the car and the film amount of about 44 ft (13.5 m) for a full color change. The labor is affected by the two large door panels that need careful installation as single pieces. The condition of the paint also matters, since old or repainted panels may need extra preparation. A partial job or chrome delete uses less film and less time than a full wrap.

  • Film for a full wrap: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Chubasco wraps by generation

Swipe sideways. Tap a card for the full description.

Maserati Chubasco, first generation, factory photo
Factory color shown

1990–1990 Chubasco coupe (first generation)

1990–1990coupe (2 doors)171.9 in (4,365 mm)

The first generation Maserati Chubasco left the factory in 1990 with a coupe body and two doors. Paint age on a car of these years may be original or repainted, so a test spot comes before a full wrap. The installer checks adhesion on a small area because old paint can fail under fresh film. The body length of 171.9 in (4,365 mm) and the two long doors set the main layout for the wrap.

Two long side doors: each door is one large piece of film.

Film: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Roof, hood, chrome delete and PPF on a Chubasco

The Chubasco chrome delete and partial wrap options let an owner change the look without a full color change. A partial wrap on this car covers the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film is also available as a clear film on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Maserati Chubasco: body, cut-outs and film

The Maserati Chubasco vinyl wrap is shaped by a coupe body with two long doors and a length of 171.9 in (4,365 mm). The single body style means the wrap layout is the same for every car of this model. The two doors are large pieces of film that need careful alignment and stretching. The car's compact size keeps the total film amount modest for a sports coupe.

Chubasco wrap ideas usually start with the two long side doors, since each door is one large piece of film. There are no unusual cut-outs on the main panels, so the wrap can flow without many seams. The door handles and side mirrors are separated to wrap them properly. The badges and window trim can stay in place, but a clean edge around them takes extra knife work.

Someone counting how much vinyl to wrap a Chubasco will find that the single generation from 1990 has no earlier or later body to compare. The film estimate stays the same for a coupe of these years: about 44 ft (13.5 m) of standard cast film. A design with chrome or patterned film brings the total to about 56 ft (17 m). There is no change between generations because this page covers one body only.

Questions about wrapping a Maserati Chubasco

How much vinyl does it take to wrap a Maserati Chubasco?

A full wrap of a Maserati Chubasco takes about 44 ft (13.5 m) of 60-inch (1.52 m) cast film. If the design uses chrome or patterned film, the amount rises to about 56 ft (17 m). These figures come from the single coupe body of the 1990 generation, which is the only one in the catalog.

Can I wrap only the hood or the roof of a Chubasco?

Yes, you can wrap only the hood or the roof of a Chubasco. A partial wrap on this car includes the roof, hood, or mirror caps as separate jobs. A chrome delete covers the window trim and badges with black film. This is a smaller job than a full wrap and uses less film.

Is a Chubasco hard to wrap?

A Chubasco is not the hardest car to wrap, but the two long side doors add work. Each door is one large piece of film that must be laid down without wrinkles or overstretching. The body length of 171.9 in (4,365 mm) is manageable, but the coupe shape has curved areas near the roof and sills that need heat. Paint age on a 1990 car can also make surface prep slower.

How many generations of the Chubasco does this page cover?

This page covers one generation of the Maserati Chubasco, the first and only generation from 1990. The car had a single coupe body style with two doors. The wrap estimates and notes are based on that generation.