Wraps by car

Rover P3 wrap

The Rover P3 wrap page covers the one-generation sedan produced in 1948 and 1949. A full vinyl wrap of this classic body takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. Plan for about 62 ft (19 m) if you choose chrome or patterned film.

1generations16.5 mof film for a full wrap

Rover P3, first generation, factory photo
Rover P3, first generation. Factory color shown.

Rover P3 wrap colors and ideas

  • Rover P3 black wrap
  • Rover P3 white wrap
  • Rover P3 gray wrap
  • Rover P3 silver wrap
  • Rover P3 red wrap
  • Rover P3 blue wrap
  • Rover P3 green wrap
  • Rover P3 yellow wrap
  • Rover P3 orange wrap
  • Rover P3 purple wrap
  • Rover P3 pink wrap
  • Rover P3 teal wrap
  • Rover P3 brown wrap
  • Rover P3 gold wrap
  • Rover P3 chrome wrap
  • Rover P3 color shift wrap
  • Rover P3 carbon fiber wrap
  • Rover P3 camo and patterned wrap

How much vinyl to wrap a Rover P3

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1948–1949sedan (4 doors)173.2 in (4,400 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m)

Rover P3 wrap cost factors

Rover P3 wrap cost depends mainly on film choice, the condition of the 1948–1949 panels, and how much trim you remove. A chrome or patterned film adds about 8 ft (2.5 m) to the base estimate. Time spent on old paint prep and cut-outs also affects the final quote.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).
  • Body: sedan (4 doors).

Rover P3 wraps by generation

Swipe sideways. Tap a card for the full description.

Rover P3, first generation, factory photo
Factory color shown

1948–1949 Rover P3 sedan (first generation)

1948–1949sedan (4 doors)173.2 in (4,400 mm)

The first generation Rover P3 was built for only two years, from 1948 to 1949. Paint on these sedans may be original or repainted, so a test spot is wise before a full vinyl wrap. An installer checks adhesion on an inconspicuous area before committing to the whole body.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 62 ft (19 m).

Roof, hood, chrome delete and PPF on a Rover P3

A partial wrap on a Rover P3 often covers the roof, hood, or mirror caps. A chrome delete transforms the bright window trim and badges with black film. Paint protection film (PPF) is a clear option for the front end, guarding the nose and the leading edges of the fenders.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Rover P3: body, cut-outs and film

A Rover P3 vinyl wrap covers a four-door sedan measuring 173.2 in (4,400 mm) long. The body has separate fenders and a large greenhouse, so material use is close to the full-car estimate. The single body style keeps cutting patterns simple for an experienced installer.

Rover P3 wrap ideas start with the bright window trim and badges, which are often wrapped in gloss black for a chrome delete. The door handles and mirrors come off for clean edges. The rear plate area and the front grille surround need careful inlays and relief cuts.

To work out how much vinyl to wrap a Rover P3, you measure one body because this page lists only the 1948–1949 sedan. The film estimate remains the same across those two production years. Original paint condition varies, so extra film is useful for test panels and re-cuts.

Questions about wrapping a Rover P3

How much vinyl does it take to wrap a Rover P3?

It takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast vinyl film to wrap a Rover P3 sedan. If the design uses chrome or patterned film, allow about 62 ft (19 m). These figures are for the 1948–1949 body listed on this page.

Can I wrap only the hood or the roof of a Rover P3?

Yes, you can wrap only the hood or the roof of a Rover P3. Smaller jobs like mirror caps and a chrome delete on the window trim and badges are also possible. These partial wraps use less film than a full body wrap.

Is a Rover P3 hard to wrap?

A Rover P3 is harder to wrap than a modern car because the body is 173.2 in (4,400 mm) long with separate fenders and many cut-outs. The window trim, badges, and door handles need precise knifeless tape work. The age of the paint may also demand extra surface preparation.

How many generations of the Rover P3 does this page cover?

This page covers one generation of the Rover P3, the sedan produced in 1948 and 1949. No other body styles or generations are listed in the catalog for this model.