Wraps by car

Rover SD1 wrap

The Rover SD1 wrap page covers the single generation of this full-size hatchback, produced from 1976 to 1986. A full vinyl wrap of the Rover SD1 takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. This guide explains the wrap process, material amounts, and what to expect on this classic British car.

1generations16.5 mof film for a full wrap

Rover SD1, first generation, factory photo
Rover SD1, first generation. Factory color shown.

Rover SD1 wrap colors and ideas

  • Rover SD1 black wrap
  • Rover SD1 white wrap
  • Rover SD1 gray wrap
  • Rover SD1 silver wrap
  • Rover SD1 red wrap
  • Rover SD1 blue wrap
  • Rover SD1 green wrap
  • Rover SD1 yellow wrap
  • Rover SD1 orange wrap
  • Rover SD1 purple wrap
  • Rover SD1 pink wrap
  • Rover SD1 teal wrap
  • Rover SD1 brown wrap
  • Rover SD1 gold wrap
  • Rover SD1 chrome wrap
  • Rover SD1 color shift wrap
  • Rover SD1 carbon fiber wrap
  • Rover SD1 camo and patterned wrap

How much vinyl to wrap a Rover SD1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1976–1986hatchback (5 doors)185.0 in (4,700 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Rover SD1 wrap cost factors

The Rover SD1 wrap cost depends on the size of the car, the film choice, and the condition of the paint. The car is 185.0 in (4,700 mm) long, so a full wrap uses about 54 ft (16.5 m) of film. A chrome or patterned film raises the material amount to about 69 ft (21 m), which adds to the cost. The number of cut-outs and the prep work on older paint also affect the final figure.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: hatchback (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Rover SD1 wraps by generation

Swipe sideways. Tap a card for the full description.

Rover SD1, first generation, factory photo
Factory color shown

1976–1986 Rover SD1 hatchback (first generation)

1976–1986hatchback (5 doors)185.0 in (4,700 mm)

The first generation Rover SD1 is a full-size hatchback built from 1976 to 1986. Panels on a car of these years may be original or repainted, so a test spot comes before a full wrap. The installer checks paint adhesion in a small hidden area to avoid lifting the film. This step protects the paint and gives the vinyl a smooth surface.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Rover SD1

A partial wrap on the Rover SD1 can cover the roof, hood, or mirror caps without wrapping the whole car. A chrome delete covers the window trim and badges with black film for a different look. Clear paint protection film (PPF) on the front end shields the paint from stone chips. These smaller jobs use less film and can be finished faster than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Rover SD1: body, cut-outs and film

The Rover SD1 vinyl wrap must handle one large hatchback body style with five doors. The car measures 185.0 in (4,700 mm) long, so a full wrap uses more film than a compact car. Its long, flat panels are straightforward to cover, but the single body style means every wrap follows the same cut plan. Installers count the tailgate and four doors as separate panels for a clean finish.

The tailgate of the Rover SD1 includes the rear glass, so the film ends at the edge of the glass. This leaves a clean boundary and avoids cutting on the glass itself. The door handles, badges, and trim need cut-outs, and these parts can stay on the car. The wrap film can follow the body lines of the hatchback without removing major panels.

There is only one production run for the Rover SD1, so the film estimate stays the same from 1976 to 1986. The body size and shape did not change in a way that affects how much vinyl to wrap a Rover SD1. A wrapper who has done one SD1 can repeat the pattern on another car of this generation. The single generation keeps the material count simple.

Questions about wrapping a Rover SD1

How much vinyl does it take to wrap a Rover SD1?

A full wrap of a Rover SD1 takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. This figure covers the entire hatchback body of the single generation. If you choose chrome or patterned film, the estimate rises to about 69 ft (21 m).

Can I wrap only the hood or the roof of a Rover SD1?

Yes, you can wrap only the hood or the roof of a Rover SD1. Partial wraps on this car commonly include the roof, hood, and mirror caps. These smaller areas let you change the look without the material cost of a full wrap.

Is a Rover SD1 hard to wrap?

The Rover SD1 is not the easiest car to wrap because of its size and the tailgate glass. The car is 185.0 in (4,700 mm) long, so installers handle large panels. The tailgate includes the rear glass, so the film must end cleanly at the edge of the glass. This edge work adds time compared with a solid metal panel.

How many generations of the Rover SD1 does this page cover?

This page covers one generation of the Rover SD1. The car was produced from 1976 to 1986 with a single body style. All wrap information on this page applies to that generation.