Wraps by car

Rover P4 wrap

The Rover P4 wrap page covers this classic sedan from its single generation, produced from 1949 to 1964. A full wrap of the newest body takes about 56 ft (17 m) of 60-inch (1.52 m) cast vinyl wrap. Owners looking for a vinyl wrap will find the key measurements and preparation notes here.

1generations17 mof film for a full wrap

Rover P4, first generation, factory photo
Rover P4, first generation. Factory color shown.

Rover P4 wrap colors and ideas

  • Rover P4 black wrap
  • Rover P4 white wrap
  • Rover P4 gray wrap
  • Rover P4 silver wrap
  • Rover P4 red wrap
  • Rover P4 blue wrap
  • Rover P4 green wrap
  • Rover P4 yellow wrap
  • Rover P4 orange wrap
  • Rover P4 purple wrap
  • Rover P4 pink wrap
  • Rover P4 teal wrap
  • Rover P4 brown wrap
  • Rover P4 gold wrap
  • Rover P4 chrome wrap
  • Rover P4 color shift wrap
  • Rover P4 carbon fiber wrap
  • Rover P4 camo and patterned wrap

How much vinyl to wrap a Rover P4

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1949–1964sedan (4 doors)178.3 in (4,528 mm)about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

Rover P4 wrap cost factors

Rover P4 wrap cost depends on the size of the car and the condition of its paint. At 178.3 in (4,528 mm) long, this sedan needs about 56 ft (17 m) of film for a full color change. The amount of chrome trim and the number of cut-outs affect the labor time. Paint age and any previous repairs also influence how much preparation the panels need.

  • Film for a full wrap: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).
  • Body: sedan (4 doors).

Rover P4 wraps by generation

Swipe sideways. Tap a card for the full description.

Rover P4, first generation, factory photo
Factory color shown

1949–1964 Rover P4 sedan (first generation)

1949–1964sedan (4 doors)178.3 in (4,528 mm)

The first generation Rover P4 wrap calls for care because the paint age on a car of these years may be original or repainted. Panels from 1949–1964 can have different paint conditions from one door to the next. A test spot comes before a full wrap to check how the film adheres. The installer will then know if any panel needs extra cleaning or repair.

Film: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on a Rover P4

A partial wrap on a Rover P4 can cover the roof, hood, or mirror caps. A Rover P4 chrome delete includes the window trim and badges covered with black film. Paint protection film (PPF) is another option, with clear film on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Rover P4: body, cut-outs and film

For a Rover P4 vinyl wrap, the sedan body measures 178.3 in (4,528 mm) in length. This size puts the car in the range where a full wrap is a full-day job for an experienced installer. The four doors and long roof mean you will use most of the film estimate. A wrap on this body needs careful planning around the rear wheel spats.

Rover P4 wrap ideas start with the parts that need cut-outs or come off. The door handles, badges, and the side trim strips are removed before film goes on. The front grille surround and the rear light bezels call for precise cut-outs. The bumpers come off for a clean edge along the body.

How much vinyl to wrap a Rover P4 depends on the generation you are working with. This page covers the single generation from 1949 to 1964, so the film estimate stays the same across those years. Early cars and late cars share the same body length, but panel fit can vary slightly. When you count film, allow about 64 ft (19.5 m) if you are using chrome or patterned film.

Questions about wrapping a Rover P4

How much vinyl does it take to wrap a Rover P4?

A full wrap of a Rover P4 takes about 56 ft (17 m) of 60-inch (1.52 m) cast film. That figure is for the newest body of this single generation. If the wrap uses chrome or patterned film, the estimate rises to about 64 ft (19.5 m).

Can I wrap only the hood or the roof of a Rover P4?

Yes, you can wrap only the hood or the roof of a Rover P4. A partial wrap on this car can cover the roof, hood, or mirror caps. You may also have a chrome delete done on the window trim and badges. PPF on the front end is another smaller job.

Is a Rover P4 hard to wrap?

A Rover P4 is not the easiest car to wrap because of its size and the number of parts that come off. The sedan is 178.3 in (4,528 mm) long, so you need a large clean work area. The door handles, badges, side trim, and bumpers are removed before film goes on. The chrome grille surround and rear light bezels also need precise cut-outs.

How many generations of the Rover P4 does this page cover?

This page covers one generation of the Rover P4, produced from 1949 to 1964. The sedan body stayed the same across those years, so the film estimate does not change. You will find all the wrap details for that single generation here.