Wraps by car

Lancia Lybra wrap

The Lancia Lybra wrap guide covers the mid-size sedan and wagon built from 1999 to 2006. This one-generation car needs about 54 ft (16.5 m) of 60-inch (1.52 m) cast film for a full vinyl wrap. The figure rises to about 64 ft (19.5 m) when the wrap uses chrome or patterned film.

1generations16.5 mof film for a full wrap

Lancia Lybra, first generation, factory photo
Lancia Lybra, first generation. Factory color shown.

Lancia Lybra wrap colors and ideas

  • Lybra black wrap
  • Lybra white wrap
  • Lybra gray wrap
  • Lybra silver wrap
  • Lybra red wrap
  • Lybra blue wrap
  • Lybra green wrap
  • Lybra yellow wrap
  • Lybra orange wrap
  • Lybra purple wrap
  • Lybra pink wrap
  • Lybra teal wrap
  • Lybra brown wrap
  • Lybra gold wrap
  • Lybra chrome wrap
  • Lybra color shift wrap
  • Lybra carbon fiber wrap
  • Lybra camo and patterned wrap

How much vinyl to wrap a Lancia Lybra

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1999–2006sedan, wagon (4 or 5 doors)175.8 in (4,466 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

Lybra wrap cost factors

Lybra wrap cost depends on the size of the car, the film type and the work the shop has to do. A full wrap on a 175.8 in (4,466 mm) sedan or wagon takes about 54 ft (16.5 m) of cast film, while chrome or patterned film pushes that to about 64 ft (19.5 m). The wagon's tailgate and the number of cut-outs also change the labor a shop quotes.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).
  • Body: sedan, wagon (4 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Lybra wraps by generation

Swipe sideways. Tap a card for the full description.

Lancia Lybra, first generation, factory photo
Factory color shown

1999–2006 Lybra sedan, wagon (first generation)

1999–2006sedan, wagon (4 or 5 doors)175.8 in (4,466 mm)

The first generation Lancia Lybra from 1999 to 2006 came as a four-door sedan or a five-door wagon. The style decides the panel plan and the film amount, because the wagon has a tailgate and a taller rear roof. Both bodies use the same 60-inch film, but a wagon wrap calls for more material and more cutting around the rear glass.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on a Lybra

If a full wrap is too much, the Lybra offers smaller jobs: a roof, hood or mirror caps in film, a chrome delete on the window trim and badges, or paint protection film (PPF) on the front end. The wagon's roof is larger than the sedan's, so a roof wrap on the wagon uses more film. A chrome delete turns the bright trim black and is a good way to change the look without wrapping the whole body.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Lancia Lybra: body, cut-outs and film

A Lancia Lybra vinyl wrap plan starts with the body style because the sedan and wagon share the same 175.8 in (4,466 mm) length but have different rear panels. The wagon has a taller roof and a tailgate, so it takes more film on the rear half than the four-door sedan. Both styles have four doors, and the wagon's fifth door adds one more cut-out to the job.

Lybra wrap ideas work around the tailgate, which holds the rear glass and leaves the film ending at the edge of the glass. The installer cuts around the glass and keeps the wrap off the rubber seal, which takes patience on the wagon. Door handles, mirrors and badges come off or get cut around for a clean edge.

When you count how much vinyl to wrap a Lybra, remember there is only one generation, so the panel sizes stay the same from 1999 to 2006. The sedan and the wagon share the front end, but the wagon's longer roof and tailgate push the film estimate higher. A full wrap on either body still fits the same 60-inch roll width, so the difference is mainly on the rear half.

Questions about wrapping a Lancia Lybra

How much vinyl does it take to wrap a Lancia Lybra?

It takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film to wrap a Lancia Lybra, or about 64 ft (19.5 m) for chrome or patterned film. These figures cover the full body of the sedan or wagon from 1999 to 2006. The installer needs a little extra for waste around the wheel arches and the bumpers.

Which Lybra body takes more film?

The wagon takes more film than the sedan, because it has a taller roof, longer rear side glass and a full tailgate. The sedan's trunk lid is smaller than the wagon's rear door, so the wagon uses more of the 54 ft (16.5 m) estimate. In practice the wagon ends up closer to the upper end of that range, while the sedan is often a bit under.

Can I wrap only the hood or the roof of a Lybra?

Yes, you can wrap only the hood or the roof of a Lybra. The shop can do a partial wrap on the roof, hood or mirror caps, and the wagon's larger roof means that single panel uses more film than the sedan's roof. This is a way to change one area without buying film for the whole car.

Is a Lybra hard to wrap?

The Lybra is not a hard car to wrap, but the wagon's tailgate with its built-in rear glass adds work, because the film ends at the edge of the glass and the seal has to be cut clean. At 175.8 in (4,466 mm) long it is a mid-size car, so the doors and fenders are straightforward. The front bumper and the mirrors still need care, but no panel is unusually curved.