Wraps by car

Lancia Prisma wrap

The Lancia Prisma wrap page covers the first generation sedan produced from 1982 to 1989. A full vinyl wrap of this car takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. Chrome or patterned film requires about 57 ft (17.5 m) due to extra material for aligning patterns. All wrap estimates are based on the original four-door sedan body.

1generations14 mof film for a full wrap

Lancia Prisma, first generation, factory photo
Lancia Prisma, first generation. Factory color shown.

Lancia Prisma wrap colors and ideas

  • Prisma black wrap
  • Prisma white wrap
  • Prisma gray wrap
  • Prisma silver wrap
  • Prisma red wrap
  • Prisma blue wrap
  • Prisma green wrap
  • Prisma yellow wrap
  • Prisma orange wrap
  • Prisma purple wrap
  • Prisma pink wrap
  • Prisma teal wrap
  • Prisma brown wrap
  • Prisma gold wrap
  • Prisma chrome wrap
  • Prisma color shift wrap
  • Prisma carbon fiber wrap
  • Prisma camo and patterned wrap

How much vinyl to wrap a Lancia Prisma

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1982–1989sedan (4 doors)164.6 in (4,181 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m)

Prisma wrap cost factors

Prisma wrap cost depends on the film type, the condition of the original paint, and the amount of disassembly needed. A car of this age may need extra prep work if panels have been repainted or have rust spots. Using chrome or patterned film adds about 25 percent more material than a standard color change wrap. The single body style and compact size keep the labor estimate simpler than on newer cars.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).
  • Body: sedan (4 doors).

Prisma wraps by generation

Swipe sideways. Tap a card for the full description.

Lancia Prisma, first generation, factory photo
Factory color shown

1982–1989 Prisma sedan (first generation)

1982–1989sedan (4 doors)164.6 in (4,181 mm)

The first generation Lancia Prisma was built from 1982 to 1989 as a four-door sedan. Because the car is from this period, the paint may be original or repainted on different panels. A test spot on each panel is recommended before a full wrap to check how the film adheres to older paint. This single generation is the only body style covered on this page.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).

Roof, hood, chrome delete and PPF on a Prisma

Smaller jobs on a Lancia Prisma include a partial wrap of the roof, hood, or mirror caps. Prisma chrome delete covers the window trim and badges with black film instead of bright metal. Paint protection film on the front end uses clear film to guard the bumper, hood edge, and fender tips. Each of these options uses less material than a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Lancia Prisma: body, cut-outs and film

A Lancia Prisma vinyl wrap focuses on one body style, the four-door sedan. The car measures 164.6 in (4,181 mm) long, which makes film planning straightforward for a compact classic. The roof, hood, and trunk lid are flat enough to wrap cleanly without excess stretching. The upright sedan shape keeps the rocker panels and rear pillars easy to reach.

Prisma wrap ideas start with the window trim and badges, which are the main parts that need cut-outs. Door handles and mirrors can be wrapped in place or removed for a neater edge around the recesses. The front grille and rear license plate area require precise trimming around the openings. The roof drip rails are best done with the doors open so the film tucks under the rubber seals.

How much vinyl to wrap a Prisma stays the same across its single generation, since every car shares the same body dimensions. There are no factory body style changes between 1982 and 1989 that would alter the film estimate. An installer only needs to re-measure if a car has aftermarket body parts or rust repair panels. The 46 ft (14 m) figure works for a stock sedan with no extra spoilers or side skirts.

Questions about wrapping a Lancia Prisma

How much vinyl does it take to wrap a Lancia Prisma?

It takes about 46 ft (14 m) of 60-inch (1.52 m) cast film to wrap a Lancia Prisma. For chrome or patterned film, plan for about 57 ft (17.5 m) to allow for matching the design at seams. These figures cover the first generation sedan body from 1982 to 1989.

Can I wrap only the hood or the roof of a Prisma?

Yes, you can wrap only the hood or the roof of a Prisma. A partial wrap of the hood, roof, or mirror caps is a common way to change the look without using as much film as a full wrap. This option also lets you test a color or finish on one panel before committing to the whole car.

Is a Prisma hard to wrap?

A Prisma is not hard to wrap if the paint is sound and the trim is removed carefully. The compact sedan shape has no deep curves that force the film to overstretch. The main extra work comes from the age of the car, since old paint may need a test spot and a deeper cleaning before the vinyl goes on.

How many generations of the Prisma does this page cover?

This page covers one generation of the Lancia Prisma, the first generation built from 1982 to 1989. There are no other generations in this catalog to compare with. All the film sizes and wrap notes on this page apply to that four-door sedan.