Wraps by car

Plymouth Duster wrap

A Plymouth Duster wrap is a full color change for a two-door coupe built from 1969 to 1976. This guide covers one generation of the Duster. A complete wrap of the body takes about 52 ft (16 m) of 60-inch (1.52 m) cast film. Add roughly 67 ft (20.5 m) if you choose chrome or patterned film for the wrap.

1generations16 mof film for a full wrap

Plymouth Duster, first generation, factory photo
Plymouth Duster, first generation. Factory color shown.

Plymouth Duster wrap colors and ideas

  • Duster black wrap
  • Duster white wrap
  • Duster gray wrap
  • Duster silver wrap
  • Duster red wrap
  • Duster blue wrap
  • Duster green wrap
  • Duster yellow wrap
  • Duster orange wrap
  • Duster purple wrap
  • Duster pink wrap
  • Duster teal wrap
  • Duster brown wrap
  • Duster gold wrap
  • Duster chrome wrap
  • Duster color shift wrap
  • Duster carbon fiber wrap
  • Duster camo and patterned wrap

How much vinyl to wrap a Plymouth Duster

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1969–1976coupe (2 doors)195.8 in (4,973 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)

Duster wrap cost factors

Duster wrap cost depends on the film type, the condition of the paint, and the amount of labor for a 195.8 in (4,973 mm) car. A full wrap on this two-door coupe uses about 52 ft (16 m) of 60-inch cast film, or about 67 ft (20.5 m) for chrome or patterned film. The two long doors each require a single large sheet, which adds time for careful application. Any bodywork or paint correction before the wrap also changes the final cost.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Duster wraps by generation

Swipe sideways. Tap a card for the full description.

Plymouth Duster, first generation, factory photo
Factory color shown

1969–1976 Duster coupe (first generation)

1969–1976coupe (2 doors)195.8 in (4,973 mm)

The first generation Plymouth Duster was produced from 1969 to 1976 as a two-door coupe. Paint on a car of these years may be original or repainted, so a test spot comes before a full wrap. This generation is the only Duster body in the catalog. A full wrap of this body needs about 52 ft (16 m) of 60-inch cast film.

Two long side doors: each door is one large piece of film.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Roof, hood, chrome delete and PPF on a Duster

A partial wrap on a Plymouth Duster is a smaller job that covers selected panels such as the roof, hood, or mirror caps. Duster chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. These options use less film than a full wrap and focus on the areas you want to change or protect.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Plymouth Duster: body, cut-outs and film

The Plymouth Duster vinyl wrap follows a single body style: a coupe with two long doors. The car is 195.8 in (4,973 mm) long, a size large enough to require careful planning of film panels. Each door is one large piece of film, so the installer must handle wide sheets without wrinkles. The simple shape has fewer body lines than many modern cars, which helps the film lay flat.

Duster wrap ideas can include a full color change or accent work on this classic body. The two long side doors are the main pieces of film, and each door is one large sheet. The installer may remove door handles, mirrors, and trim to tuck the film edges cleanly. Badges and window trim come off before the wrap and go back on after the film is set.

How much vinyl to wrap a Duster is a number tied to the first generation body. This page shows one generation of the Duster, produced from 1969 to 1976. The film estimate is about 52 ft (16 m) for a full wrap with standard cast film. A wrap with chrome or patterned film needs about 67 ft (20.5 m) because the pattern repeat adds waste.

Questions about wrapping a Plymouth Duster

How much vinyl does it take to wrap a Plymouth Duster?

A full wrap of a Plymouth Duster takes about 52 ft (16 m) of 60-inch (1.52 m) cast film. That figure is for the coupe body of the newest generation covered on this page. If the wrap uses chrome or patterned film, the amount is about 67 ft (20.5 m).

Can I wrap only the hood or the roof of a Duster?

Yes, you can wrap only the hood or the roof of a Duster. A partial wrap covers selected panels such as the roof, hood, or mirror caps. This uses less film than a full wrap and can match or contrast with the original paint.

Is a Duster hard to wrap?

A Duster is manageable to wrap, but its large, flat panels and two long doors add work. Each door is one large piece of film, so the installer must handle a wide sheet without creases. The car's 195.8 in (4,973 mm) length means more film and more time to cover the body.

How many generations of the Duster does this page cover?

This page covers one generation of the Plymouth Duster, the first generation produced from 1969 to 1976. The guide describes the two-door coupe body only. No other generations are in the catalog for this model.