Wraps by car

Plymouth Laser wrap

The Plymouth Laser wrap page covers the first and only generation, built from 1989 to 1994, and its two-door coupe body. A full vinyl wrap of this compact car takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 54 ft (16.5 m).

1generations14 mof film for a full wrap

Plymouth Laser, first generation, factory photo
Plymouth Laser, first generation. Factory color shown.

Plymouth Laser wrap colors and ideas

  • Laser black wrap
  • Laser white wrap
  • Laser gray wrap
  • Laser silver wrap
  • Laser red wrap
  • Laser blue wrap
  • Laser green wrap
  • Laser yellow wrap
  • Laser orange wrap
  • Laser purple wrap
  • Laser pink wrap
  • Laser teal wrap
  • Laser brown wrap
  • Laser gold wrap
  • Laser chrome wrap
  • Laser color shift wrap
  • Laser carbon fiber wrap
  • Laser camo and patterned wrap

How much vinyl to wrap a Plymouth Laser

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1989–1994coupe (2 doors)170.5 in (4,330 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m)

Laser wrap cost factors

Laser wrap cost depends on the film chosen and the amount needed for this 170.5 in (4,330 mm) coupe. A full wrap takes about 46 ft (14 m) of 60-inch cast film, while chrome or patterned film pushes the total to about 54 ft (16.5 m). The labor for two long doors and the front end also affects the total.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Laser wraps by generation

Swipe sideways. Tap a card for the full description.

Plymouth Laser, first generation, factory photo
Factory color shown

1989–1994 Laser coupe (first generation)

1989–1994coupe (2 doors)170.5 in (4,330 mm)

The first generation Plymouth Laser was built from 1989 to 1994, and that paint age means panels may be original or repainted. A test spot on the paint before a full wrap is necessary to check adhesion. If the paint is original and in good condition, the film will stick well, but repainted panels can be risky.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).

Roof, hood, chrome delete and PPF on a Laser

Partial wrap options for the Laser include the roof, hood, and mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Plymouth Laser: body, cut-outs and film

The Plymouth Laser vinyl wrap is sized for a compact two-door coupe with a length of 170.5 in (4,330 mm). The single body style means every Laser uses the same amount of film for a full wrap. The two long side doors are each one large piece of film, so seams are easy to place along the door edges.

Laser wrap ideas start with the two long side doors, which take one large piece of film per door. The long door panels need care during installation to avoid wrinkles and stretch marks. The front bumper and mirrors require cut-outs, and the door handles and antenna should be removed for a clean finish.

For someone who counts film, knowing how much vinyl to wrap a Laser is simple because the car was made in one generation from 1989 to 1994. There were no changes in body size, so the film estimate stays the same for every year. A coupe shape with a long roof and short deck uses less film than a sedan.

Questions about wrapping a Plymouth Laser

How much vinyl does it take to wrap a Plymouth Laser?

A full wrap of a Plymouth Laser takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. If you use chrome or patterned film, you need about 54 ft (16.5 m). These figures apply to the only generation, the 1989–1994 coupe.

Can I wrap only the hood or the roof of a Laser?

Yes, you can wrap only the hood or the roof of a Laser. Partial wrap jobs on this car often include the roof, hood, and mirror caps. You can also choose a chrome delete for the window trim and badges.

Is a Laser hard to wrap?

A Laser is not hard to wrap, but the two long side doors add some work because each door is one large piece of film. The car is compact at 170.5 in (4,330 mm), so the roof and hood are straightforward. The front bumper and mirrors need cut-outs, which adds a little time.

How many generations of the Laser does this page cover?

This page covers one generation of the Plymouth Laser, produced from 1989 to 1994. There were no other generations, so all Lasers share the same body style and film requirements.