Wraps by car

Plymouth Neon wrap

A Plymouth Neon wrap covers the full body with vinyl wrap. The Neon was produced from 1993 to 2001 and this guide covers its first generation. This model came as a coupe or sedan, both with two or four doors. A full wrap of the newest body takes about 46 ft (14 m) for the coupe to 49 ft (15 m) for the sedan.

1generations14 mof film for a full wrap

Plymouth Neon, first generation, factory photo
Plymouth Neon, first generation. Factory color shown.

Plymouth Neon wrap colors and ideas

  • Neon black wrap
  • Neon white wrap
  • Neon gray wrap
  • Neon silver wrap
  • Neon red wrap
  • Neon blue wrap
  • Neon green wrap
  • Neon yellow wrap
  • Neon orange wrap
  • Neon purple wrap
  • Neon pink wrap
  • Neon teal wrap
  • Neon brown wrap
  • Neon gold wrap
  • Neon chrome wrap
  • Neon color shift wrap
  • Neon carbon fiber wrap
  • Neon camo and patterned wrap

How much vinyl to wrap a Plymouth Neon

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1993–2001coupe, sedan (2 or 4 doors)171.8 in (4,364 mm) to 174.4 in (4,430 mm)about 46 ft (14 m) for the coupe to 49 ft (15 m) for the sedan, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 61 ft (18.5 m)

Neon wrap cost factors

Neon wrap cost depends on the body style, the film type, and the labor for this compact car. The coupe uses less film than the sedan, and a color change wrap on either style needs extra work for door jambs. The simple body lines of the Neon mean less disassembly than on a larger car, but the bumpers and moldings still add time. The final number changes with the condition of the paint and the chosen film finish.

  • Film for a full wrap: about 46 ft (14 m) for the coupe to 49 ft (15 m) for the sedan, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 61 ft (18.5 m).
  • Body: coupe, sedan (2 or 4 doors).

Neon wraps by generation

Swipe sideways. Tap a card for the full description.

Plymouth Neon, first generation, factory photo
Factory color shown

1993–2001 Neon coupe, sedan (first generation)

1993–2001coupe, sedan (2 or 4 doors)171.8 in (4,364 mm) to 174.4 in (4,430 mm)

The first generation Plymouth Neon came as a coupe or sedan with two or four doors. The style decides the panel plan and the film amount for a wrap. The coupe's shorter rear section uses less film than the sedan's longer trunk area. Both styles share the same front end and door shapes, so the main difference is at the rear.

Film: about 46 ft (14 m) for the coupe to 49 ft (15 m) for the sedan, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Neon

A partial wrap on a Plymouth Neon can cover just the roof, hood, or mirror caps. Another option is a chrome delete that covers window trim and badges with black film. Paint protection film (PPF) can be applied as a clear film on the front end to guard against stone chips. These smaller jobs use less film and take less time than a full wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Plymouth Neon: body, cut-outs and film

A Plymouth Neon vinyl wrap must fit a compact body with coupe and sedan styles. The coupe measures 171.8 in (4,364 mm) and the sedan up to 174.4 in (4,430 mm), so the film amount differs between the two. The flat sides and simple bumpers keep panel planning straightforward. The roof and hood are large enough to need wide film sections.

Neon wrap ideas start with the parts that need cut-outs or come off. The door handles, mirrors, and antenna base require precise trimming or removal. The front and rear bumpers come off for edge wrapping, and the side moldings need to be pulled before film goes on. The badges and trim pieces are removed for a clean finish.

Figuring how much vinyl to wrap a Neon starts with the single generation in this catalog. The body styles changed little from 1993 to 2001, so the panel sizes stay consistent for counting film. A coupe needs about 46 ft (14 m) of 60-inch (1.52 m) cast film. A sedan needs about 49 ft (15 m), and patterned film can take up to 61 ft (18.5 m).

Questions about wrapping a Plymouth Neon

How much vinyl does it take to wrap a Plymouth Neon?

Yes, a full wrap of a Plymouth Neon takes about 46 ft (14 m) for the coupe to 49 ft (15 m) for the sedan. Those numbers use 60-inch (1.52 m) cast film. If the film has a pattern or a chrome finish, plan for up to about 61 ft (18.5 m). The exact amount depends on the body style and the installer's cutting plan.

Which Neon body takes more film?

The Neon sedan takes more film than the coupe. The sedan's longer rear end and trunk add surface area compared to the coupe's shorter deck. A sedan wrap needs about 49 ft (15 m) of 60-inch (1.52 m) film, while the coupe needs about 46 ft (14 m). The difference comes mainly from the rear quarter panels and trunk lid.

Can I wrap only the hood or the roof of a Neon?

Yes, you can wrap only the hood or only the roof of a Neon as a partial wrap. These jobs cover a small panel with vinyl and use much less film than a full wrap. Mirror caps and a chrome delete on window trim and badges are other partial options. A clear paint protection film on the front end protects the hood and bumper without changing the color.

Is a Neon hard to wrap?

A Neon is not very hard to wrap, but its size and a few parts add work. The compact body means some panels are small and the bumpers curve around, so the installer spends more time on stretching and relief cuts. The door handles, mirrors, and moldings need to come off or be cut around carefully. The simple flat sides of the Neon help keep the job manageable.