Wraps by car

Mitsubishi Delica wrap

The Mitsubishi Delica wrap page covers five generations of the van and the vinyl wrap film each body needs. The newest fifth generation runs from 2007 to now and uses about 70 feet (21.5 meters) of 60-inch (1.52 m) cast film for a full wrap. Chrome or patterned film on the same body takes about 82 feet (25 meters).

5generations21.5 mof film for a full wrap

Mitsubishi Delica, fifth generation, factory photo
Mitsubishi Delica, fifth generation. Factory color shown.

Mitsubishi Delica wrap colors and ideas

  • Delica black wrap
  • Delica white wrap
  • Delica gray wrap
  • Delica silver wrap
  • Delica red wrap
  • Delica blue wrap
  • Delica green wrap
  • Delica yellow wrap
  • Delica orange wrap
  • Delica purple wrap
  • Delica pink wrap
  • Delica teal wrap
  • Delica brown wrap
  • Delica gold wrap
  • Delica chrome wrap
  • Delica color shift wrap
  • Delica carbon fiber wrap
  • Delica camo and patterned wrap

How much vinyl to wrap a Mitsubishi Delica

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2007–nowvan (5 doors)173.2 in (4,400 mm) to 189.0 in (4,800 mm)about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 82 ft (25 m)
1994–2007van (4 doors)184.6 in (4,690 mm) to 199.0 in (5,055 mm)about 74 ft (22.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 85 ft (26 m)
1986–1999van (4 doors)165.0 in (4,190 mm)about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m)
1979–1986van (4 doors)157.5 in (4,000 mm)about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)
1968–1979van (3 doors)——

Delica wrap cost factors

Delica wrap cost depends on the size of the body and the amount of film from the estimate. The first generation is the smallest at about 59 feet (18 m), and the fourth generation is the largest at about 74 feet (22.5 m) of 60-inch (1.52 m) cast film. Partial wraps reduce the film but still need time on the tall body. The number of doors and the sliding tracks also add steps to the job.

  • Film for a full wrap: about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 82 ft (25 m).
  • Body: van (5 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.
  • A tall body (73.8 in (1,875 mm)): the roof is wrapped from a platform.
  • Restyled in 2018: bumpers and lights differ between the versions, and so do the film cuts.

Delica wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi Delica, fifth generation, factory photo
Factory color shown

2007–now Delica van (fifth generation)

2007–nowvan (5 doors)173.2 in (4,400 mm) to 189.0 in (4,800 mm)

The fifth generation Delica from 2007 onward has sliding side doors that shape the wrap. The door tracks stay bare, so the film is cut along them and never covers the track area. This leaves a clean edge that follows the door's movement. A wrap plan for this body always starts with those cuts.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

A tall body (73.8 in (1,875 mm)): the roof is wrapped from a platform.

Film: about 70 ft (21.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 82 ft (25 m).

Mitsubishi Delica, fourth generation, factory photo
Factory color shown

1994–2007 Delica van (fourth generation)

1994–2007van (4 doors)184.6 in (4,690 mm) to 199.0 in (5,055 mm)

The fourth generation Delica was restyled in 1997, and that changes the film cuts. Bumpers and lights changed, so film cut for a pre-1997 van does not fit a post-1997 van. An installer counts the van as two different wrap shapes within this generation. The year of the car tells which cut to use.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

A tall body (78.0 in (1,980 mm)): the roof is wrapped from a platform.

Film: about 74 ft (22.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 85 ft (26 m).

Mitsubishi Delica, third generation, factory photo
Factory color shown

1986–1999 Delica van (third generation)

1986–1999van (4 doors)165.0 in (4,190 mm)

The third generation Delica covers years that overlap with the newer body from 1994 to 1999. An owner of a car from those years checks which body it is because the two generations were built at the same time. The third generation body is shorter and uses less film than the fourth generation. Checking the body style and the year avoids a wrong film estimate.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

A tall body (77.6 in (1,970 mm)): the roof is wrapped from a platform.

Film: about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).

Mitsubishi Delica, second generation, factory photo
Factory color shown

1979–1986 Delica van (second generation)

1979–1986van (4 doors)157.5 in (4,000 mm)

The second generation Delica has a tall body that affects the wrap. The roof is wrapped from a platform because the van stands 71.7 inches (1,820 mm) high. Working from a platform takes more time and care than wrapping a lower vehicle. The roof film is one piece and must be laid without creases.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

A tall body (71.7 in (1,820 mm)): the roof is wrapped from a platform.

Film: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Mitsubishi Delica, first generation, factory photo
Factory color shown

1968–1979 Delica van (first generation)

1968–1979van (3 doors)

The first generation Delica from 1968 to 1979 has old paint that calls for a test spot. Panels may be original or repainted, and old paint can fail under fresh vinyl wrap. A small test spot applied and removed before the full wrap shows whether the paint will hold. If the paint is weak, the wrap is not applied until the panel is refinished.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Two long side doors: each door is one large piece of film.

Roof, hood, chrome delete and PPF on a Delica

A Mitsubishi Delica can take a partial wrap instead of a full one. Jobs include the roof, hood, and mirror caps, or a Delica chrome delete on the window trim and badges. Paint protection film (PPF) can be applied as clear film on the front end. Each partial job uses less film and focuses on the areas that matter.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Mitsubishi Delica: body, cut-outs and film

A Mitsubishi Delica vinyl wrap starts with the body styles and sizes of the generation you own. The newest vans measure 173.2 inches (4,400 mm) to 189.0 inches (4,800 mm) long and have five doors. Earlier generations are shorter, with the first generation at 157.5 inches (4,000 mm) and three doors. More length and doors mean more film and more time to wrap.

Delica wrap ideas start with the van's sliding side doors. The door tracks stay bare, and the film is cut along them on every generation. The tall body, 71.7 to 78.0 inches (1,820 to 1,980 mm) depending on generation, means the roof is wrapped from a platform. The first generation also has two long side doors, each wrapped as one large piece of film.

How much vinyl to wrap a Delica depends on the generation, because the bodies grew over time. The first generation uses about 59 feet (18 m) of 60-inch (1.52 m) cast film, while the fourth generation uses about 74 feet (22.5 m). A restyle in 1997 on the fourth generation changed bumpers and lights, so film cuts differ between early and late versions.

Questions about wrapping a Mitsubishi Delica

How much vinyl does it take to wrap a Mitsubishi Delica?

A Mitsubishi Delica of the newest fifth generation takes about 70 feet (21.5 meters) of 60-inch (1.52 m) cast film for a full wrap. This is the estimate for the 2007–now body, and chrome or patterned film takes about 82 feet (25 meters). Older generations take less or more depending on their size.

Are the sliding doors of a Delica wrapped?

Yes, the sliding doors of a Delica are wrapped, but the door tracks stay bare. The film is cut along the tracks so the door can still slide without touching the film. The tracks themselves are not wrapped. Every generation of the Delica has this detail.

Which years of the Delica take the same film cuts?

Mitsubishi Delica generations take the same film cuts within a single body until a restyle. The fourth generation changed in 1997, so 1994–1997 vans and 1997–2007 vans need different cuts for bumpers and lights. The fifth generation was restyled in 2018, so 2007–2018 vans and 2018–now vans are not identical. Other generations have one cut each.

Can I wrap only the hood or the roof of a Delica?

Yes, you can wrap only the hood or the roof of a Mitsubishi Delica. The partial wrap list includes the roof, hood, and mirror caps. A chrome delete covers the window trim and badges, and paint protection film (PPF) can go on the front end as clear film. Those options are smaller than a full wrap.