Wraps by car

Mitsubishi RVR wrap

A Mitsubishi RVR wrap changes the look of this small SUV with a full vinyl wrap. The catalog covers the three generations produced since 1991. The newest body, the third generation, takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film.

3generations17.5 mof film for a full wrap

Mitsubishi RVR, third generation, factory photo
Mitsubishi RVR, third generation. Factory color shown.

Mitsubishi RVR wrap colors and ideas

  • Mitsubishi RVR black wrap
  • Mitsubishi RVR white wrap
  • Mitsubishi RVR gray wrap
  • Mitsubishi RVR silver wrap
  • Mitsubishi RVR red wrap
  • Mitsubishi RVR blue wrap
  • Mitsubishi RVR green wrap
  • Mitsubishi RVR yellow wrap
  • Mitsubishi RVR orange wrap
  • Mitsubishi RVR purple wrap
  • Mitsubishi RVR pink wrap
  • Mitsubishi RVR teal wrap
  • Mitsubishi RVR brown wrap
  • Mitsubishi RVR gold wrap
  • Mitsubishi RVR chrome wrap
  • Mitsubishi RVR color shift wrap
  • Mitsubishi RVR carbon fiber wrap
  • Mitsubishi RVR camo and patterned wrap

How much vinyl to wrap a Mitsubishi RVR

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2010–nowSUV (5 doors)169.1 in (4,295 mm) to 171.9 in (4,365 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m)
1997–2002van (5 doors)176.4 in (4,480 mm)about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m)
1991–1997targa, van (3 or 4 doors)170.1 in (4,320 mm)about 51 ft (15.5 m) for the targa to 62 ft (19 m) for the van, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 72 ft (22 m)

Mitsubishi RVR wrap cost factors

A Mitsubishi RVR wrap cost depends on the body size, film choice, and labor. The first generation targa needs less film than the second generation van, which is the largest at 176.4 in (4,480 mm). Chrome or patterned film raises material use, while cut-outs around sliding doors or the tailgate glass add time.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).
  • Body: SUV (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Restyled in 2012, 2017, 2019: bumpers and lights differ between the versions, and so do the film cuts.

Mitsubishi RVR wraps by generation

Swipe sideways. Tap a card for the full description.

Mitsubishi RVR, third generation, factory photo
Factory color shown

2010–now Mitsubishi RVR SUV (third generation)

2010–nowSUV (5 doors)169.1 in (4,295 mm) to 171.9 in (4,365 mm)

The third generation Mitsubishi RVR was restyled in 2017 and 2019, changing bumpers and lights. Film cut for one version does not fit the other, so the production year matters for a wrap kit. The body length also varies slightly after the restyling, from 169.1 in (4,295 mm) to 171.9 in (4,365 mm).

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).

Mitsubishi RVR, second generation, factory photo
Factory color shown

1997–2002 Mitsubishi RVR van (second generation)

1997–2002van (5 doors)176.4 in (4,480 mm)

The second generation Mitsubishi RVR has sliding side doors that require special wrap handling. The door tracks stay bare, and the film is cut along them. This body is a five-door van with a length of 176.4 in (4,480 mm), which needs about 64 ft (19.5 m) of film.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).

Mitsubishi RVR, first generation, factory photo
Factory color shown

1991–1997 Mitsubishi RVR targa, van (first generation)

1991–1997targa, van (3 or 4 doors)170.1 in (4,320 mm)

Paint age on a first-generation Mitsubishi RVR affects wrap preparation. On a car from 1991–1997, panels may be original or repainted, so a test spot comes before a full wrap. The targa top adds complexity because the fabric is not wrapped and the film ends where it begins.

Targa body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 51 ft (15.5 m) for the targa to 62 ft (19 m) for the van, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 72 ft (22 m).

Roof, hood, chrome delete and PPF on a Mitsubishi RVR

A partial wrap on a Mitsubishi RVR can cover the roof, hood, or mirror caps. Chrome delete is also available to cover window trim and badges with black film. Paint protection film (PPF) can be applied as clear film on the front end.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Mitsubishi RVR: body, cut-outs and film

A Mitsubishi RVR vinyl wrap follows the body of each generation, so sizes differ. The third generation is a five-door SUV between 169.1 in (4,295 mm) and 171.9 in (4,365 mm) long. The second generation is a longer five-door van at 176.4 in (4,480 mm). The first generation came as a targa or a van with three or four doors, at 170.1 in (4,320 mm).

Mitsubishi RVR wrap ideas start with the parts that need cut-outs or come off. The third generation has a tailgate with the rear glass in it, so the film ends at the edge of the glass. On the second generation and the van version of the first, sliding side doors keep the door tracks bare. The first generation also offered a targa body where a fabric top is not wrapped.

How much vinyl to wrap a Mitsubishi RVR depends on the generation and body style. The first generation needs about 51 ft (15.5 m) for the targa and 62 ft (19 m) for the van. The second generation uses about 64 ft (19.5 m), and the third generation about 57 ft (17.5 m). Chrome or patterned film adds roughly 8 to 12 ft (2.5 to 3.5 m) because of pattern matching.

Questions about wrapping a Mitsubishi RVR

How much vinyl does it take to wrap a Mitsubishi RVR?

Approximately 57 ft (17.5 m) of 60-inch (1.52 m) cast film is needed for the newest Mitsubishi RVR body. This figure applies to the third generation, which has been in production since 2010. The amount varies for older generations.

Which years of the Mitsubishi RVR take the same film cuts?

The third generation Mitsubishi RVR from 2010 to 2016 takes one set of film cuts, while the 2017 and 2019 restyled versions take different cuts. The second generation from 1997–2002 and the first generation from 1991–1997 each have their own cuts. Within the first generation, the targa and van bodies also differ.

Can I wrap only the hood or the roof of a Mitsubishi RVR?

Yes, you can wrap only the hood or the roof of a Mitsubishi RVR. Partial wraps are available for the roof, hood, and mirror caps on any generation. A smaller job like this uses less film than a full wrap.

Is a Mitsubishi RVR hard to wrap?

A Mitsubishi RVR is moderately hard to wrap because of its body features. The sliding side doors on the second generation and first-generation van require cutting along the door tracks. The third generation has a tailgate with rear glass that limits film placement.