Wraps by car

Chrysler Dynasty wrap

The Chrysler Dynasty wrap page covers the first and only generation of this mid-size sedan, produced from 1988 to 1993. A full vinyl wrap of the Dynasty takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film needs about 66 ft (20 m) because of waste from matching patterns.

1generations16.5 mof film for a full wrap

Chrysler Dynasty, first generation, factory photo
Chrysler Dynasty, first generation. Factory color shown.

Chrysler Dynasty wrap colors and ideas

  • Dynasty black wrap
  • Dynasty white wrap
  • Dynasty gray wrap
  • Dynasty silver wrap
  • Dynasty red wrap
  • Dynasty blue wrap
  • Dynasty green wrap
  • Dynasty yellow wrap
  • Dynasty orange wrap
  • Dynasty purple wrap
  • Dynasty pink wrap
  • Dynasty teal wrap
  • Dynasty brown wrap
  • Dynasty gold wrap
  • Dynasty chrome wrap
  • Dynasty color shift wrap
  • Dynasty carbon fiber wrap
  • Dynasty camo and patterned wrap

How much vinyl to wrap a Chrysler Dynasty

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1988–1993sedan (4 doors)192.0 in (4,877 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m)

Dynasty wrap cost factors

Dynasty wrap cost depends on the amount of film, condition of the paint, and the labor for a four-door sedan that is 192.0 in (4,877 mm) long. A color change wrap uses about 54 ft (16.5 m) of cast film, while chrome delete adds time because the window trim is long and narrow. Paint that is rough or repainted requires extra prep before the vinyl is applied.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).
  • Body: sedan (4 doors).

Dynasty wraps by generation

Swipe sideways. Tap a card for the full description.

Chrysler Dynasty, first generation, factory photo
Factory color shown

1988–1993 Dynasty sedan (first generation)

1988–1993sedan (4 doors)192.0 in (4,877 mm)

The first generation Chrysler Dynasty ran from 1988 to 1993, and its paint age matters before a wrap. On a car of these years panels may be original or repainted, and a test spot comes before a full wrap. An original panel can have fading that affects adhesion, while a repaint may be thicker or softer. The wrap installer checks each panel before quoting the job.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).

Roof, hood, chrome delete and PPF on a Dynasty

A partial wrap on a Chrysler Dynasty covers the roof, hood, or mirror caps without wrapping the whole sedan. A chrome delete covers the window trim and badges with black film for a different look. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. These jobs use less film than a full wrap but still need the same care at the edges.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Chrysler Dynasty: body, cut-outs and film

A Chrysler Dynasty vinyl wrap is a color change wrap on a four-door sedan body that is 192.0 in (4,877 mm) long. The car has a fairly upright greenhouse and long flat sides, which means the film is cut from large panels without extreme contours. The trunk and hood are large enough to need wide pieces from a 60-inch roll, but there are no complex curves like on a modern crossover.

Dynasty wrap ideas start with the chrome trim, which is bright on every trim level and can be covered with black film for a chrome delete. The wrap installer removes the badges before applying vinyl, and the door handles and mirrors come off for a clean edge. The recessed areas around the grille and tail lights take extra time because the film must be cut and tucked without lifting.

When you count how much vinyl to wrap a Dynasty, you only need to plan for one generation, the 1988–1993 sedan. There are no body style changes during these years, so the film estimate stays the same whether the car is from the first or last year. The only difference may be in the paint condition, because an older repaint can change how the vinyl sticks.

Questions about wrapping a Chrysler Dynasty

How much vinyl does it take to wrap a Chrysler Dynasty?

It takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film to wrap a Chrysler Dynasty. If you use chrome or patterned film, plan on about 66 ft (20 m) because matching patterns creates waste. This is based on the sedan body that is 192.0 in (4,877 mm) long.

Can I wrap only the hood or the roof of a Dynasty?

Yes, you can wrap only the hood or the roof of a Dynasty. A partial wrap covers the roof, hood, or mirror caps, and it uses less film than a full wrap. The edges still need to be wrapped around the panel and tucked cleanly.

Is a Dynasty hard to wrap?

A Dynasty is not hard to wrap, but the chrome trim adds work. Every trim has bright window surrounds and badges that need extra cutting or removal. The long flat sides are easy to film, but the recessed grille and tail lights take time to tuck the vinyl.

How many generations of the Dynasty does this page cover?

This page covers one generation of the Chrysler Dynasty, the first generation produced from 1988 to 1993. There were no other generations of the Dynasty. The single body style is a four-door sedan.