Wraps by car

Chrysler Viper wrap

This page covers the Chrysler Viper wrap for the first generation, produced from 1992 to 2002. The Viper was available as a convertible and a coupe, with this catalog holding one generation. A full vinyl wrap of the latest body uses about 43 ft (13 m) for the convertible to 49 ft (15 m) for the coupe.

1generations13 mof film for a full wrap

Chrysler Viper, first generation, factory photo
Chrysler Viper, first generation. Factory color shown.

Chrysler Viper wrap colors and ideas

  • Viper black wrap
  • Viper white wrap
  • Viper gray wrap
  • Viper silver wrap
  • Viper red wrap
  • Viper blue wrap
  • Viper green wrap
  • Viper yellow wrap
  • Viper orange wrap
  • Viper purple wrap
  • Viper pink wrap
  • Viper teal wrap
  • Viper brown wrap
  • Viper gold wrap
  • Viper chrome wrap
  • Viper color shift wrap
  • Viper carbon fiber wrap
  • Viper camo and patterned wrap

How much vinyl to wrap a Chrysler Viper

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1992–2002convertible, coupe (2 doors)175.1 in (4,448 mm) to 176.8 in (4,490 mm)about 43 ft (13 m) for the convertible to 49 ft (15 m) for the coupe, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 56 ft (17 m)

Viper wrap cost factors

Viper wrap cost depends on which body style you have, because a coupe needs more film than a convertible. The length of the car, 175.1 in (4,448 mm) to 176.8 in (4,490 mm), changes how much material is used over the long hood and rear deck. The body is wrapped with 60-inch (1.52 m) cast film, so the price follows the total area covered.

  • Film for a full wrap: about 43 ft (13 m) for the convertible to 49 ft (15 m) for the coupe, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 56 ft (17 m).
  • Body: convertible, coupe (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.
  • Two long side doors: each door is one large piece of film.

Viper wraps by generation

Swipe sideways. Tap a card for the full description.

Chrysler Viper, first generation, factory photo
Factory color shown

1992–2002 Viper convertible, coupe (first generation)

1992–2002convertible, coupe (2 doors)175.1 in (4,448 mm) to 176.8 in (4,490 mm)

The open top on the first-generation Viper is not wrapped when the car is a convertible with a fabric roof. The film ends where the fabric top begins, so the installer cuts a clean line along the edge of the roof opening. If the car has a folding hard top, that top is wrapped as panels of its own.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Two long side doors: each door is one large piece of film.

Film: about 43 ft (13 m) for the convertible to 49 ft (15 m) for the coupe, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 56 ft (17 m).

Roof, hood, chrome delete and PPF on a Viper

A partial wrap on the Viper can cover just the roof, hood, or mirror caps without doing the whole car. Viper chrome delete is another option: the window trim and badges are covered with black film. For clear protection, paint protection film (PPF) goes on the front end to guard the nose and hood.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Chrysler Viper: body, cut-outs and film

A Chrysler Viper vinyl wrap has to follow the curves of a long sports car body that measures 175.1 in (4,448 mm) to 176.8 in (4,490 mm). The convertible and coupe share the same two-door layout, so the side sections are nearly identical. Each long side door is covered as one large piece of film to keep the wrap seamless.

Viper wrap ideas start with the long side doors, because each door is one large piece of film with no cut line in the middle. The door handles and mirrors are removed so the film can tuck behind them cleanly. On the convertible, the fabric top is not wrapped and the film ends where the top begins.

To work out how much vinyl to wrap a Viper, the difference between generations is small because this catalog lists only the first generation. The 1992–2002 cars came as a convertible and a coupe, and a coupe needs more film than the open car. A full wrap takes about 43 ft (13 m) on the convertible and 49 ft (15 m) on the coupe.

Questions about wrapping a Chrysler Viper

How much vinyl does it take to wrap a Chrysler Viper?

A full wrap of a Chrysler Viper needs about 43 ft (13 m) for the convertible to 49 ft (15 m) for the coupe. These figures assume 60-inch (1.52 m) cast film, and chrome or patterned film can push the total to about 56 ft (17 m).

Is the top of a Viper wrapped?

Yes, the top of a Viper is wrapped when the car has a folding hard top, and that top is done as separate panels. The fabric top of the convertible is not wrapped, and the film ends where the top begins.

Which Viper body takes more film?

A coupe Viper takes more film than a convertible, because the hard roof adds surface area. The estimate is about 43 ft (13 m) for the convertible and 49 ft (15 m) for the coupe.

Can I wrap only the hood or the roof of a Viper?

Yes, you can wrap only the hood or the roof of a Viper as a partial wrap. A partial wrap can also cover just the mirror caps, and it is a smaller job than a full-color change.