Wraps by car

Chrysler Prowler wrap

The Chrysler Prowler wrap turns this distinctive sports car into a one-of-a-kind build with a full vinyl wrap. The Prowler was produced in a single generation, the 2001–2002 convertible. A complete color change wrap on the newest body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film.

1generations14 mof film for a full wrap

Chrysler Prowler, first generation, factory photo
Chrysler Prowler, first generation. Factory color shown.

Chrysler Prowler wrap colors and ideas

  • Prowler black wrap
  • Prowler white wrap
  • Prowler gray wrap
  • Prowler silver wrap
  • Prowler red wrap
  • Prowler blue wrap
  • Prowler green wrap
  • Prowler yellow wrap
  • Prowler orange wrap
  • Prowler purple wrap
  • Prowler pink wrap
  • Prowler teal wrap
  • Prowler brown wrap
  • Prowler gold wrap
  • Prowler chrome wrap
  • Prowler color shift wrap
  • Prowler carbon fiber wrap
  • Prowler camo and patterned wrap

How much vinyl to wrap a Chrysler Prowler

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2001–2002convertible (2 doors)165.0 in (4,190 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Prowler wrap cost factors

Prowler wrap cost depends on the film type, the finish, and the labor involved in the car's curved panels and convertible edges. A standard cast vinyl full wrap uses about 46 ft (14 m) of 60-inch (1.52 m) material, while chrome or patterned film adds about 5 ft (1.5 m) and higher film expense. The small two-seat body reduces material compared to larger cars, but the long hood and wide fenders still demand careful installation.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Prowler wraps by generation

Swipe sideways. Tap a card for the full description.

Chrysler Prowler, first generation, factory photo
Factory color shown

2001–2002 Prowler convertible (first generation)

2001–2002convertible (2 doors)165.0 in (4,190 mm)

The first-generation Chrysler Prowler is an open-top convertible, and the fabric top is not wrapped with vinyl. The film ends where the top meets the body, so the installer must trim a clean line along the windshield header and the rear deck. A folding hard top would be wrapped as separate panels, but the Prowler never had one.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Prowler

A partial wrap on this Chrysler Prowler covers the hood, mirror caps, or rear deck for a subtle color change. A chrome delete (bright trim covered with black film) handles the window trim and badges, though the Prowler has minimal brightwork. Paint protection film (PPF) as a clear film on the front end is ideal for a low sports car that picks up road debris.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Chrysler Prowler: body, cut-outs and film

A Chrysler Prowler vinyl wrap follows the compact 165.0 in (4,190 mm) convertible body, with film ending where the fabric top begins. The two-door sports car has no fixed roof, so the wrap covers the hood, fenders, doors, rear deck, and bumpers only. Its short length and low height mean less surface area than on a modern sedan, but the curved front fenders and rear haunches require careful stretching.

Prowler wrap ideas start with a full color change, and a clean install depends on removing or cutting around several parts. The mirrors, door handles, badges, and antenna come off for a seamless finish, while the front and rear lights need precise cut-outs. The fabric top is not wrapped, so the film edge must be trimmed neatly where the top meets the body.

To estimate how much vinyl to wrap a Prowler, use the single generation, 2001–2002, as the only reference. The body dimensions and panel count do not change between model years, so the material requirement stays the same. A full wrap needs about 46 ft (14 m) of standard 60-inch (1.52 m) cast film, while chrome or patterned film requires about 51 ft (15.5 m).

Questions about wrapping a Chrysler Prowler

How much vinyl does it take to wrap a Chrysler Prowler?

Yes, a Chrysler Prowler takes about 46 ft (14 m) of 60-inch (1.52 m) cast film for a full vinyl wrap. Chrome or patterned film requires a bit more, around 51 ft (15.5 m). The car's small size and open top reduce the amount of material compared to a closed coupe.

Is the top of a Prowler wrapped?

No, the fabric top of a Prowler is not wrapped. Vinyl film does not adhere well to fabric, and the top must remain flexible to open and close. The wrap ends at the edges of the top, with a clean trim line along the body.

Can I wrap only the hood or the roof of a Prowler?

Yes, you can wrap only the hood or the rear deck of a Prowler as a partial wrap. The hood is a large, flat panel that works well for a contrasting color. Mirror caps and rear deck are other options for a smaller change.

Is a Prowler hard to wrap?

Yes, a Prowler is moderately hard to wrap because of its convertible body and curved panels. The fabric top requires precise trimming where the film ends, and the long hood and wide fenders need stretching and relief cuts. With a cast film and experience, the job is very doable.